Curtis Instruments 908 Скачать руководство пользователя

Страница: 10 / 11

4.2 Reset Type/Level

(after or during recharge)

CTR (Charge Tracking Reset)

If the gauge is connected to the battery during

recharge, the gauge will track battery charge levels.

OCR (Open Circuit Reset)

If the gauge is disconnected from the battery during

recharge, the gauge will retain the last indication. It will

advance to full when reconnected only of the battery

voltage is above the OCR level. For standard (“B”)

reset, OCR=2.09 VPC (Volts per cell).

5. TROUBLESHOOTING

The following checklist should help you troubleshoot any

problem with Model 908.

Problem

Possible Cause

No display

Terminals not connected or improper voltage

Stays at FULL

Instrument voltage does not match battery
voltage; B+ connected to the wrong terminal
(see page 11)

Will not reset

Instrument voltage does not match battery
voltage or battery not fully charged

Reset without
charging battery

Not connected directly to battery terminals

EMPTY too soon

B+ connected to wrong terminal, or
instrument voltage does not match battery
voltage, or terminals not connected directly
to battery

Содержание 908












Результаты поиска

Содержание 908

Отзывы:

Похожие инструкции для 908

Бренды по названию

Популярные бренды

Curtis Instruments 908, Руководство по эксплуатации

Результаты поиска

Содержание 908

Отзывы:

Похожие инструкции для 908

Бренды по названию

Популярные бренды