manualshive.com logo in svg

Current Tools RotaBoom 700SI, Руководство по эксплуатации, техническому обслуживанию, безопасности и каталогу запасных частей

Поделиться
Скачать
Current Tools RotaBoom 700SI Скачать руководство пользователя страница 5

ALWAYS use recommended accessories. Consult this manual for 

recommended accessories. The use of improper accessories may 

cause risk of injury.

ALWAYS keep hands and feet away from pinch points such as 

bending shoes, roller supports and conduit when bender is in use.

Operator must ALWAYS face the front of the bender with the 

bending degree scale visible and maintain a minimum of 3 feet  

distance from the bender while the conduit is being bent. All 

other personnel must remain out of the area while the bender is 

in operation. 

ALWAYS use appropriate shoe groove and roller support for  

the type and size conduit to be bent.

If bending shoe will not turn, STOP unit and unplug before  

checking for any obstructions. 

DO NOT use bender or attachments to do a job for which  

it was not designed.

ALWAYS keep conduit under control when unloading.

ALWAYS keep the path of the bending conduit clear of  

obstructions. Make sure all obstacles are clear of the bending  

path BEFORE you bend the conduit.

Be sure handle is bolted securely to the bender frame before 

moving or lifting the bender.

NEVER stand on bender. Serious injury could occur if the bender  

is tipped or if the bending shoe is unintentionally contacted.

ALWAYS wear approved safety glasses when the bender is  

in operation. 

ALWAYS wear proper apparel. Do not wear loose clothing, 

gloves, neckties, rings, bracelets, or other jewelry which may  

get caught in moving parts. Non-slip footwear is recommended.  

Wear protective hair covering to contain long hair.

ALWAYS keep children away. All visitors should be kept a safe  

distance from work area.

ALWAYS make bender childproof with lockouts, master switches 

or by unplugging unit.

The bender and some accessories exceed 50 lbs. and will 

require more than one person to lift, transport and assemble.

Only use the bender for its intended purpose as specified  

in this manual.

ALWAYS use this bender in a dry, well lighted area.

ALWAYS maintain bender with care. Keep bender clean for  

best and safest performance.

5

IMPORTANT SAFETY INFORMATION

 

— 

continued

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

WARNING

DANGER

CAUTION

Содержание RotaBoom 700SI




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды