Current Tools RotaBoom 700SI Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 35

Current Tools RotaBoom 700SI Скачать руководство пользователя страница 12

12

Figure 12

GENERAL BENDING INSTRUCTIONS

Bending instructions for:
  1/2" thru 2" RIGID conduit
  1/2" thru 1 1/4" EMT conduit
  1/2" thru 1 1/4" IMC conduit
  1/2" thru 2" 40 mil PVC coated RIGID conduit
  1/2" thru 2" schedule 40 pipe

See pages 10 and 11 for mounting shoe and roller support.

Be sure to match the appropriate shoe with its corresponding roller support.
1. Mark pipe/conduit to the desired length. Note that a 2" minimum distance

from the end of the conduit to the bending mark is required to eliminate

flattening the end of the pipe/conduit. See Figure 12.

NOTE: Stub-up and Offset dimensions can be found on the bending charts

on pages 20 thru 23 of this manual or on the bending instruction decal on

top of each bender.

2. Rotate the bending shoe to 10 degrees below the 0 ( zero ) degree setting,

as shown in Figure 12 below.

DANGER

NEVER operate this bender in an explosive atmosphere. Injury or Death may occur.

2"

MINIMUM

BENDING

MARK

HOOK

2"

MINIMUM

BENDING

MARK

HOOK

0°

-10°

«
...
10
11
12
13
14
...
»

Содержание RotaBoom 700SI




































Отзывы:

Нет отзывов