Current Tools RotaBoom 700SI Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 35

Current Tools RotaBoom 700SI Скачать руководство пользователя страница 17

17

Figure 17b

Figure 17a

SQUEEZE ADJUSTMENT PROCEDURE FOR

1 1/2" AND 2" EMT & IMC ROLLER SUPPORTS

The 1 1/2" and 2" rollers on the single shoe EMT Roller Support and the 1 1/2"

and 2" rollers on the single shoe IMC Roller Support on the 77 bender have a

Squeeze Adjustment feature if wrinkling or side marking becomes a problem

during the bending process. This feature allows you to increase or decrease

the amount of pressure applied to the conduit during bending, thereby elimi-

nating these problems. Begin with the 7/8" starting location of the adjusting

bolts as shown in Figure 17a.
1. If wrinkling occurs, pressure against the conduit during the bending process

must increase. To increase the squeeze ( pressure ), loosen both set screws

and turn both adjusting bolts one-half turn clockwise. Bend one piece of

conduit to test the adjustment, and if wrinkling still occurs, repeat the

procedure. Once you have achieved a good bend, tighten both set screws.
NOTE: Both adjusting bolts MUST be in contact with the bender leg.

See Figure 17a.

2. If side marking occurs, pressure against the conduit during the bending

process must be decreased. To decrease the squeeze ( pressure ), loosen

both set screws and turn both adjusting bolts one-half turn counter-clock

wise. Bend one piece of conduit to test the adjustment, if side marking

still occurs, repeat the procedure. Once you have achieved a good bend,

tighten both set screws.
NOTE: Both adjusting bolts MUST be in contact with the bender leg. See

Figure 17a.

STOP

BOTH ADJUSTING BOLTS

MUST CONTACT BENDER LEG

BENDER LEG

ADJUSTING BOLT

STARTING LOCATION

OF ADJUSTING BOLT

7/8"

SET SCREW

«
...
15
16
17
18
19
...
»

Содержание RotaBoom 700SI




































Отзывы:

Нет отзывов