Current Tools RotaBoom 700SI Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

Current Tools RotaBoom 700SI Скачать руководство пользователя страница 18

18

MAINTENANCE

1. The Gear Box is filled with oil at the factory and should not require periodic

flushing. If the Gear Box is opened for repair, flush by filling the unit with

an AGMA #7 oil. Next, run the unit with no load for 3 minutes. Then, drain

and refill the unit with 28 fluid ounces of an AGMA #7 oil such as the ones

listed below.

Amoco – Amoco Worm Gear Oil

Chevron – Cylinder Oil 460X

Exxon – CYLESSTIC TK460

Mobil – 600 W Cylinder Oil

Shell – Sun Gear Oil 7C

2. To inspect FRONT #60 chain tension:
• Remove front cover plate.

• To adjust, loosen hex bolt with 3/4 wrench and rotate chain tensioner

toward chain as shown until chain moves no more than a total of 1/4".

See Figure 18 below.

• Grease chain periodically with a good quality MP grease.

Figure 18

ALWAYS disconnect power supply before removing any guards or covers and

before servicing this bender. Failure to do so may result in serious injury or death.

WARNING

«
...
16
17
18
19
20
...
»

Содержание RotaBoom 700SI




































Отзывы:

Нет отзывов