background image

Diagrams  |  

JetTouch

®

 Workstation  

|    3    

Table of Contents

About This Guide ...................................................................................................2

Specifications .......................................................................................................2

Diagrams ..............................................................................................................3

Getting Started .....................................................................................................5

How to Process a Transaction ..............................................................................10

How to Use the Supervisor Menu ......................................................................... 11

Stopping Conditions and Recovery Steps .............................................................. 18

Daily Cleaning Procedures .................................................................................... 19

About This Guide

This guide covers basic and some advanced features of the JetTouch® workstation, 
which is a touch-screen PC terminal that runs JetTouch casino settlement software. 
The versatile workstation communicates with JetScan® and JetScan iFX® scanners,  
as well as JetSort® coin sorters, to provide a comprehensive back-office solution. 
For assistance with advanced workstation setup and configuration, 

please contact  

a Cummins Allison representative

.

Specifications

Please follow the operating guidelines below:

Diagrams

Operating Guidelines

Temperature range

50ºF – 90ºF 

Humidity range

20% – 80%,  without  condensation 

Ventilation

Allow at least 1 inch of air clearance from ventilation 
holes on the PC terminal. Air must flow freely around 
the terminal at all times. 

Power supply

The customer must provide a single-phase, dedicated 
power line that meets the machine’s power rating(s). 
Use a properly grounded circuit breaker in compliance 
with applicable local electrical code.

Diagrams

This section outlines features of the JetTouch workstation. 

PC Terminal

Port Panel

The port panel is located under the display, as shown below.

Communication options include:

• 

Four RS-232 serial communication ports. 

Ports 3 and 4 need an adapter harness. 

The port labeled COM4 is pre-configured for a printer and requires one of the 
harnesses for connection. Two harnesses are included with every purchase.

• 

Six USB ports. 

Four are located under the display, and two are located in the panel 

on the left side of the display near the power switch. 

• 

An external VGA port.

 The port can be used for a security camera video feed or an 

external display.

2  |  

JetTouch

®

 Workstation

  |  Table of Contents

Power switch and  

USB port panel 

Touch-screen display

LED indicator

UPS battery under base

Port panel

Содержание JetTouch











Отзывы: