CUMMINS ALLISON JetCount 4020 Скачать руководство пользователя страница 42

Страница: 42 / 45

JetCount

Currency Counter

All Models

Term

Definition

Factory Mode

A special set of pre-programmed defaults for the JetCount Setup Fields.

Hopper

The area on top of the JetCount where documents are placed for processing.

Reset

Key is used to reset counts to zero. The RESET key is also used to restart the

machine after a stopping condition.

Setup Fields

There are pre-operating conditions that can be assigned or controlled by the

operator. Once they are set, they remain set (even if the machine is turned OFF)

unless reset by re-entering the setup process.

Stacker

The area at the bottom front of the JetCount where processed documents are

delivered.

Strap

The quantity of documents to be prepared for banding.

Suspect Document

Sensitivity

JetCount allows the setting of different sensitivity levels per denomination for

the detection of suspect documents. The lower the sensitivity, the greater the

opportunity to pass a counterfeit note. The higher the sensitivity, the greater the

opportunity to stop on a good (non-counterfeit) note.

Содержание JetCount 4020














































Результаты поиска

Содержание JetCount 4020

Отзывы:

Похожие инструкции для JetCount 4020

Бренды по названию

Популярные бренды

CUMMINS ALLISON JetCount 4020, Руководство по эксплуатации

Результаты поиска

Содержание JetCount 4020

Отзывы:

Похожие инструкции для JetCount 4020

Бренды по названию

Популярные бренды