manualshive.com logo in svg

Cumberland INT-4807, Инструкция по установке и эксплуатации

Поделиться
Скачать
Cumberland INT-4807 Скачать руководство пользователя страница 20

20

PNEG-1323 

Integra Feed-Link

6. Stand Alone Remote Mounted Display Units

Junction Box

NOTE: If display units are mounted inside, then 

you will need a junction box.

1. Remove the multi-hole grommet from the 

display unit and exchange it with the 
grommet provided with the junction box.

2. Connect the 

Red

 wire from load cell 1 to the 

POWER terminal labeled RED LC1. Repeat 
for each consecutive load cell cable. 
Connect the RED wire from the 10 conductor 
junction cable to the POWER terminal 
labeled RED JC.

3. Connect the 

Black

 wire from load cell 1 to the 

GROUND terminal labeled BLACK LC1. 
Repeat for each consecutive load cell cable. 
Connect the BLACK cable from the 10 
conductor junction cable to the GROUND 
terminal labeled BLACK JC.

Figure 6A 

Junction Box Terminals

4. Connect the 

White

 wire from load cell 1 to 

the left side center SIGNAL terminal labeled 
White LC1. Repeat for each consecutive 
load cell cable. 

(See Figure 6B.)

5. Connect the remaining wires (up to 8) from 

the 10 wire junction cable to the terminals 
opposite the already installed 

White

 

SIGNAL load cell wires. Match the wire color 
to the corresponding terminal labeled with 
the same color. Fasten all wires into 
terminals using a flat head screw driver. 
Then run junction cable from junction box to 
the display box. Junction cable length should 
not exceed 100'.

Figure 6B 

Always make sure all power is 
disconnected and locked out 
while any electrical work is 
being performed.

NOTE:

 

Only four (4) load 

cell cables shown.

Содержание INT-4807























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды