769-07384 P00
12/11
IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES BEFORE OPERATING THE UNIT.
Removing Unit From Carton
Assemble The Unit
Starting The Unit
Remove cap from lower
boom. Push cutting
attachment into coupler.
Turn coupler knob clockwise
to tighten.
Assemble The Unit
Mix thoroughly in separate
fuel can:
– 3.2 fl. oz. of 2-cycle
engine oil
– 1 gallon of unleaded
gasoline
NOTE:
Do not mix directly in
fuel tank.
Place unit on a level surface.
Fill fuel tank.
Press
primer bulb
10 times
,
or until fuel is visible
Crouch in starting position.
SQUEEZE
and
HOLD
throttle for
ALL
further
steps.
Pull rope
5 times
.
Move choke lever to
Position 2
and squeeze
throttle.
Pull rope
3-5 times
to start
engine. Run unit for
30-60
seconds
to warm up.
Continue to squeeze
throttle.
Move choke lever
to
Position 3
.
1
1
Remove all contents from
carton.
4
5
6
1
8
9
2
Place the D-handle over the
shaft housing and onto the
bottom clamp. Place it a
minimum of
6 inches
from the
end of the shaft grip.
Move
choke lever to
Position 1
.
Continue to squeeze
throttle.
Run unit for an
additional
60 seconds
to
complete warm-up. Unit
may be used during this
time.
7
3
Starting The Unit
10
11
12
13
14
Primer
Bulb
10 X
5 X
3-5 X
Choke Lever
Starter Rope
Fuel Cap
Throttle Control
Blade Shield /
Shield Mount
Brush Blade
Cutting
Head Shield
Cutting
Head
Line
Cutting
Blade
On/ Off Switch
D-Handle
Rapid-link™
Need Help?
Call 1-877-282-8684
DIDN’T START?
Repeat these instructions.
IF
engine fails to start after 2 attempts,
move choke lever to position 3 and pull
the starter rope until engine starts
IF
unit still fails to start, refer to the
operator’s manual for additional starting
and troubleshooting information
1 Gallon
3.2 oz
40:1
Choke Lever
Choke Lever
Min. 6"
Tools Required
• Flat blade screwdriver
• T-25 Tox screwdriver
• Locking Rod
• 13 mm closed-end
or socket wrench
Bottom
Clamp
(4) Screws
Unscrew bump knob
clockwise. Remove
inner reel and spring.
Insert
10'
of 0.105"SplitLine
®
through hole in top of reel.
Pull most of line through hole
until 3"-4" remains.
Bend short end and push it
into the other hole. Pull tight.
Wind
line tightly in direction
of arrow. Split
other end of
SplitLine
®
back 6"-7".
Push 6"-7" ends into
the holding slots.
Insert lines through eyelets in
spool. Insert spring and reel
into spool.
1
1
Hold the inner reel in place.
Tighten Bump Knob
counterclockwise
.
Reloading The Line*
3
4
5
6
7
Pull lines firmly to release
from holding slots.
1
8
Reloading The Line
2
For replacement line, call
1-877-282-8684
or go to
an authorized service dealer.
For
single line
installation or
replacement spool
installation instructions, refer to the
Replacing the
Trimming Line
section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions
are NOT part of the fast assembly instructions. Line does not need to
be installed on the initial assembly and start-up.
3"-4"
Bump
Knob
Inner
Reel
Spool
Spring
Español — Page 11
English — Page 1
Français — Page 6
NEED HELP?
CALL 1-877-282-8684 IN U.S. OR 1–800–668–1238 IN CANADA
BC210
2-Cycle Gasoline
Trimmer /
Brushcutter
Operator’s Manual