Cub Cadet 724 STE страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 30

background image

15

Figure 18

Servicing Friction Wheel Rubber

The rubber on the friction wheel is subject to wear and
should be checked after 25 hours of operation, and
periodically thereafter. Replace the friction wheel
rubber if any signs of wear or cracking are found.

•

Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.

•

Tip the snow thrower up and forward, so that it rests
on the housing.

•

Remove the six self-tapping screws from the frame
cover underneath the snow thrower.

•

Using a 7/8" wrench to hold the shaft, loosen, but
do not completely remove, the hex bolt and washer
on the left end of the shaft. See Figure 19 and
Figure 20.

•

Lightly tap the hex bolt to dislodge the ball bearing
from the right side of frame before removing the hex
bolt and washer from the left end of the shaft.

•

Move the shaft to the right and slide the friction
wheel assembly from the shaft.

•

Remove the six screws from the friction wheel
assembly (three from each side). Remove the
friction wheel rubber from between the friction
wheel plates. See Figure 18

Figure 19

•

Reassemble the new friction wheel rubber to the
friction wheel plates and hub, tightening the six
screws in rotation and with equal force.

•

Position the friction wheel assembly up onto the pin
of the shift rod assembly, and slide the shaft
through the assembly. Reassemble in reverse
order.

NOTE:

If you placed plastic film under the gas cap, be

certain to remove it.

Figure 20

Figure 21

Off Season Storage

WARNING:

Never store engine with fuel in tank

indoors or in enclosed, poorly ventilated areas where
fuel fumes may reach an open flame, spark or pilot light
as on a furnace, water heater, clothes dryer, or other
gas appliance.

•

Clean snow thrower thoroughly.

•

Lubricate as instructed above with light oil.

Friction Wheel

Drive Plate

Drive Belt

Support Bracket

Stop Bolt

Friction Wheel Rubber

Screws

Screws

Friction Wheel Plates

Hub

Hex Bolt

Track

Washer

Spacer

Sprocket

Shift Rod

Assembly

Pin

Friction Wheel

Assembly

Support

Bracket

Shaft

«
...
13
14
15
16
17
...
»

Содержание 724 STE































Отзывы:

Нет отзывов

Похожие инструкции для 724 STE

Pro Force 44553

Бренд: Toro Страницы: 44

Бренд: Black+Decker Страницы: 100

Бренд: Tanaka Страницы: 10

Бренд: Sartorius Страницы: 2

Бренд: ICP Страницы: 12

Бренд: SNOWJOE Страницы: 20

Бренд: Yard Machines Страницы: 22

Бренд: Kobalt Страницы: 16

Бренд: MTD Страницы: 24

Бренд: Worx Страницы: 12

Бренд: Worx Страницы: 152

Бренд: LOFTNESS Страницы: 36

Бренд: Meec tools Страницы: 136

Бренд: Lux Tools Страницы: 110

Бренд: Arcoaire Страницы: 6

HT19-401-003-21

Бренд: Hyper Tough Страницы: 24

Бренд: Romus Страницы: 26

TRACK SNOW THROWER

Бренд: Troy-Bild Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды