Cub Cadet 724 STE страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 30

background image

14

Belt Removal And Replacement

WARNING:

Disconnect the spark plug wire

and ground it against the engine before
performing any repairs or maintenance.

Auger Belts

•

Remove the plastic belt cover at the front of the
engine by removing the two self-tapping screws.
See Figure 15.

•

Drain the gasoline from the snow thrower, or place
a piece of plastic film under the gas cap.

•

Tip the snow thrower up and forward so that it rests
on its auger housing.

Figure 15

•

Remove the six self-tapping screws from the frame
cover underneath the snow thrower.

•

Roll the front and rear auger belts off the auger
drive pulley. See Figure 16.

•

Unhook the idler spring from the hex bolt on the
auger housing. See Figure 17.

•

Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 18.

NOTE:

It may be necessary to loosen the six nuts that

connect the frame to the auger housing to aid in belt
removal.

•

Lift the rear auger belt from the auger pulley, and
slip the belt between the support bracket and the
auger pulley. See Figure 17. Repeat this step for
the front auger belt.

•

Replace both auger drive belts by following
instructions in reverse order.

Figure 16

NOTE:

If you placed plastic film under the gas cap, be

certain to remove it before operating the snow thrower.

Drive Belt

•

Follow the first four steps of the instructions for
servicing the auger belts.

•

Pull the idler pulley up, and lift the belt off the wheel
drive pulley and friction wheel disc. See Figure 17.

•

Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 18.

•

Slip the belt between the friction wheel and drive
disc. See Figure 18. Remove and replace the belt.
Reassemble following the instructions in reverse
order.

NOTE:

The support bracket must rest on the stop bolt

after the new belt has been assembled. See Figure 18.

Figure 17

Self-Tapping
Screws

Engine

Auger Housing

Belt Cover

Auger

Drive

Belt

Drive

Pulley

Idler

Pulley

Idler

Pulley

Auger

Drive

Pulley

Wheel

Drive

Belts

Wheel

Frame

Support

Bracket

Rear

Auger

Belt

Auger

Pulley

Idler

Spring

Auger

Housing

Support

Bracket

Spring

Frame

Front

Auger

Belt

«
...
12
13
14
15
16
...
»

Содержание 724 STE































Отзывы:

Нет отзывов

Похожие инструкции для 724 STE

Бренд: Canarm Страницы: 6

Бренд: Elektror Страницы: 28

Snow Fox 769-00858 (8/03)

Бренд: Yard Machines Страницы: 32

Бренд: HART Страницы: 34

Бренд: Poulan Pro Страницы: 40

SWEEP-N-CLEAN SW48-M

Бренд: T.I.P. Страницы: 33

Бренд: Ariens Страницы: 8

Бренд: Cub Cadet Страницы: 48

LEAFJET 4101821

Бренд: Worx Страницы: 156

Бренд: Erskine Attachments Страницы: 24

Бренд: Cramer Страницы: 6

Бренд: Kubota Страницы: 15

Бренд: Vortice Страницы: 52

VORTICE LINEO Q V0

Бренд: Vortice Страницы: 52

Бренд: Sanitaire Страницы: 5

Intelli-Sense CS 10

Бренд: Labconco Страницы: 72

Бренд: YARDMAX Страницы: 9

Бренд: sunjoe Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды