CTI GG-6 Скачать руководство пользователя страница 18

Страница: 18 / 20

GG-6

Specifications (GG-6)

Specifications (GG-XM)

Input Power Requirements:

115 VAC, 3A 50/60 Hz (100-120 VAC)
230 VAC, 2A 50/60 Hz (200-240 VAC)
*230 VAC selected by switch on side of power supply

Output 24 VDC Power available for sensors and audio/visual devices:

4A @ 40°C (104°F).
2A @ 50°C (122°F).

Dimensions:

15.8” high x 14” wide x 7” deep

Weight:

14 lbs

Enclosure:

Fiberglass Reinforced Polyester NEMA 4X, IP 66, with neoprene gasket.

Continuous stainless-steel hinge. Captive screws in lid. For non-classified areas.

Temperature Range:

0°F to +122°F

Humidity Range:

0-95% RH condensing (100% intermittent), with proper conduit seals.

Sensor Inputs:

(6) 4/20 mA, 350 Ohm input impedance

Analog Outputs: (optional)

(6) Linear 4/20 mA (max input impedance: 700 Ohms)

Relay Outputs:

(6) SPDT, Form C dry contacts

8 A @ 24 VDC or 10 A @ 240 VAC

Terminal Block Plugs (Field Wiring):

26-12 AWG, torque 4 lbs-in.

User Interface:

LCD illuminated screen. Graphic display screen: 128 x 64 pixels. 8 lines x 22 characters.

Sealed membrane switches.

Certification:

ETL Listed: Conforms to UL 61010-1

Certified to CSA C22.2 No. 61010-1

Input Power Requirements:

115 VAC, 3A 50/60 Hz (100-120 VAC)
230 VAC, 2A 50/60 Hz (200-240 VAC)
*230 VAC selected by switch on side of power supply

Output 24 VDC Power available for sensors and audio/visual devices:

4A @ 40°C (104°F).
2A @ 50°C (122°F).

Dimensions:

15.8” high x 14” wide x 7” deep

Weight:

14 lbs

Enclosure:

Fiberglass Reinforced Polyester NEMA 4X, IP 66, with neoprene gasket.

Continuous stainless-steel hinge. Captive screws in lid. For non-classified areas.

Temperature Range:

0°F to +122°F

Humidity Range:

0-95% RH condensing (100% intermittent), with proper conduit seals.

Sensor Inputs:

(8) 4/20 mA, 350 Ohm input impedance

Analog Outputs:

(optional)

(8) Linear 4/20 mA (max input impedance: 700 Ohms)

Relay Outputs:

(8) SPDT, Form C dry contacts
8 A @ 24 VDC or 10 A @ 240 VAC

Terminal Block Plugs (Field Wiring):

26-12 AWG, torque 4 lbs-in.

Certification:

SGS Listed: Conforms to UL 61010-1

Certified to CSA C22.2 No. 61010-1

Содержание GG-6





















Результаты поиска

Содержание GG-6

Отзывы:

Похожие инструкции для GG-6

Бренды по названию

Популярные бренды

CTI GG-6, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GG-6

Отзывы:

Похожие инструкции для GG-6

Бренды по названию

Популярные бренды