manualshive.com logo in svg

CTC Union VRM01/24, Руководство пользователя

Поделиться
Скачать
CTC Union VRM01/24 Скачать руководство пользователя страница 52

VDSL SERIES 

 

 

 

CTC Union 

 

           

 

50 

unintentionally disconnected from the network. 

3. When cascading two devices using RJ-45 station ports at both ends of the cable 

(VRM01/24 supports auto MDIX), without crossover cable can be used.   

 

 

 

         

     

Physical Configuration 

 

If problems occur after altering the network configuration, restore the original connections, 
and try to track the problem down by implementing the new changes, one step at a time.   
Ensure that cable distances and other physical aspects of the installation do not exceed 
recommendations 
 

System Integrity 

 

As a last resort verify the switch integrity with a power-on reset.    Turn the power to the 

switch off and then on several times. If the problem still persists and you have completed all 
the preceding diagnoses, contact your dealer for assistance. 

     
       

CE Side Start Link watch dog 

             

If CE side(VDSL Modem) power on standby exceed 20 minute without connecting VDSL 

concentrator, which will start up Link watch dog, you will find Link fail, users must re-plug 
power on once to clear that and reconnecting VDSL concentrator.             
 

 
 
 
 

 

 

 

 
 
 
 
 
 
 
 
 

Содержание VRM01/24


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды