manualshive.com logo in svg

CTC Union VRM01/24, Руководство пользователя

Поделиться
Скачать
CTC Union VRM01/24 Скачать руководство пользователя страница 35

VDSL SERIES 

 

 

 

CTC Union 

 

           

 

33 

4-4-7. VLAN configurations 

A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you 
to isolate network traffic so only members of the VLAN receive traffic from the same VLAN 
members. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a 
group of network devices to another Layer 2 switch. 
However, all the network devices are still plug into the same switch physically. 
The VDSL SWITCH support port-based and 802.1Q (tagged-based) VLAN in web management 
page. 
In the default configuration, VLAN support is disable. 

 

NOTE:

   

If you change VLAN Operation Mode from No VLAN to 802.1Q, you must wait 50 seconds. 
Change VLAN mode for every time, you have to reboot the VRM01/24 for valid value. 

 
Support Port-based VLAN 

Packets can go among only members of the same VLAN group. Note all unselected ports are 
treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging 
is ignored. 

 

Support Tag-based VLAN (IEEE 802.1Q VLAN) 

Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create 
a VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to 
insert a “tag” into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the 
VLAN numbers. 

Содержание VRM01/24


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды