manualshive.com logo in svg

CTC Union VRM01/24, Руководство пользователя

Поделиться
Скачать
CTC Union VRM01/24 Скачать руководство пользователя страница 11

VDSL SERIES 

 

 

 

CTC Union 

 

           

 

9 

LED Indications 
 

The following describes the function of each LED indicator. 

         

LEDs 

 

Status 

       

Descriptions 

PWR. 
(Power LED) 

Steady 
Green 

This LED light is located at the left side on the front 
panel. It will light up (ON) to show that the product is 
receiving power. Conversely, no light (OFF) means the 
product is not receiving power. 

POST 
(Power On Self 
Test) 

Steady 
Green 

Proceed function test to myself when power on. 

ACT 
(Receiving 
LEDs) 

Steady 
Green 
Flashing 

Act Led if flashing to show data on Receiving status 

Speed100  
Speed1000 
(Speed LEDs) 

Steady 
Yellow 

Indicates that communications have been set 100 or 
1000 Mbps. Each port on the VRM01/24 is assigned an 
LED light for 100 or 1000 Base-TX connecting, else on 
10M speed. 

Steady 
Yellow 

Indicates that communications have been set to 
full-duplex operation for the indicated port   

FD 
(Full-Duplex 
LEDs ) 

Steady 
Yellow 

The indicator lights up working in Full Duplex 
And light down working in Half Duplex 

LINK LEDs 

Steady 
Green 
 

RJ21 LED is lit up to show “Link”.    The indicator both 
CO and CE side connecting OK, and light down which 
Meaning is no connecting.   

 

Содержание VRM01/24


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды