manualshive.com logo in svg

CTC Union VRM01/24, Руководство пользователя

Поделиться
Скачать
CTC Union VRM01/24 Скачать руководство пользователя страница 10

VDSL SERIES 

 

 

 

CTC Union 

 

           

 

8 

Provides one 10/100/1000Mbps auto-sensing RJ-45 Ethernet ports and one GIGA Port. 
GIGA Port support RJ-45 or GBIC Interface auto link function. You can use RJ-45 interface or 
GBIC

   

interface.

Figure Chapter 2.2 

 

 

 

 

Normal GIGA port status default in copper (RJ45), if you want to change connect media to 

fiber you must plug in GBIC fiber module.   
First, make sure fiber to fiber connecting is ready, and another fiber device must power on first, 
then reboot VRM01/24, that will be sensing and link that in Fiber optic mode. 
GIGA port RJ-45 and GBIC can’t use in the same time

,

 else that will be link in Copper 

mode(default)

.  

If you want to change GIGA port interface

 (RJ45 interface link change to   

GBIC interface link or GBIC interface link change to RJ45 interface link), 

you must reboot system 

again

. 

 

GBIC Fiber Optics 

A gigabit interface converter (GBIC) is a transceiver that converts electric currents (digital 
highs and lows) to optical signals, and optical signals to digital electric currents. The GBIC is 
typically employed in fiber optic and Ethernet systems as an interface for high-speed 
networking. The data transfer rate is 1.25 gigabit per second.   
GBIC modules allow technicians to easily configure and upgrade electro-optical 
communications networks. The typical GBIC transceiver is a plug-in module that supports 
hot-plugging (it can be removed and replaced without turning off the system). The devices 
are economical, because they eliminate the necessity for replacing entire boards at the 
system level. Upgrading can be done with any number of units at a time, from an individual 
module to all the modules in a system. GBIC(Gigabit Interface Converter), meet the Gigabit 
Interface Converter specification Rev. 5.4 (MOD_DEF4) industry standard. 

 

 

Mode 

Wavelength 

Bit Rate 

Voltage 

Power Margin 

1 LX- Single Mode 

1310nm 

1.25Gbps 

5V 

10.5db(10KM) 

2  SX- Multi Mode 

850nm 

1.25Gbps 

5V 

8.5db(550m) 

Содержание VRM01/24


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды