background image

 

 

                                                                                                                                                     

SIGNATURE 2 SERIES 

                                                                                                                                         

Main Menu

 

                             

12

:

00

 

   

 

                                                                        

1. 

To enter Main Menu, press the 

Menu/Enter

 button.

 

(Time of Day will flash)

2. 

To set the 

Time of Day

, press the 

Set/Change

 button.

 (First 

digit 

will 

flash) 

       Example 

(

12

:

00

)  -  

 

To change digit value, press the 

Set/Change

 button.

 

To accept the digit value, press the 

Menu/Enter

 button.

 

Next digit will flash to begin setting.

  

Once the last digit display is accepted, all digits will flash.

3. 

To set 

A.M.

 or 

P.M

., press the 

Menu/Enter

 button. 

  

To change digit value, press the 

Set/Change

 button. 

 

 

Example (  

 A 

 )

  

To accept the digit value, press the 

Menu/Enter

 button.

  

Once A.M. or P.M. is accepted, the next menu item will flash.

 4. 

a. To set the 

Number of Days between Backwash Cycles

 (A), press the 

Set/Change

 button.     

 

 Repeat 

instructions 

from 

step 

(2).      Example 

A - 06

 )

  

Notes:

 1) Maximum value is 29.

 

 

 2) If value set to 0, Automatic Backwash will never occur.

  

 

 3) Default setting is 6 days for filters.

  

 

 

 

           

  

5. 

To Exit Main Menu, press the 

Menu/Enter

 button.

 

Note:

 If no buttons are pressed for 60 seconds, the Main Menu will be exited automatically.

  7

Control Start-Up Procedures

-  Final Checkout -

1. Be certain that the bypass valve is in Service position and main valve is completely on.
2. Check electrical supply to be certain the cord is connected to an uninterrupted 115 volt outlet.
3. Be certain the warranty card is filled out and mailed in.
4. Leave this manual with the homeowner.

Important Notice - The plumbing system, piping, pressure tank, hot water tanks, softeners, etc. that have been exposed 
to iron bearing water may need to be cleaned of the precipitated iron that has been collected in them or iron bleed thru 
may be a problem. We suggest all tanks be drained and flushed thoroughly.

- Programming The Control Valve -

1. Set time of day.
2. Set a.m. or p.m.
3. Set number of days between backwash. (This generally will be every 4 to 6 days.)
4. Set regeneration time if other than 12:00 a.m. is desired.

Содержание REACTR RF15





















Отзывы: