Crystal CS4231A Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 76

background image

IA3-IA0

Index Address: These bits define the
address of the CS4231A register ac-
cessed by the Indexed Data register
(R1). These bits are read/write.

IA4

Allows access to indirect registers
16 - 31. Only available in MODE 2.
In MODE 1,this bit is reserved.

TRD

Transfer Request Disable: This bit,
when set, causes DMA transfers to
cease when the INT bit of the status
register is set. Independent for play-
back and capture interrupts.

0 - Transfers Enabled (PDRQ and

CDRQ occur uninhibited)

1 - Transfers Disabled (PDRQ and

CDRQ only occur if INT bit is 0)

MCE

Mode Change Enable: This bit must
be set whenever the sample fre-
quency,D3-D0 of I8, or the Interface
Configuration (I9) register is
changed. The exceptions are CEN
and PEN which can be changed "on-
the-fly". The DAC output is muted
when MCE is set. MCE or PMCE
(I16) may be used to changed the
playback data format, D7-D3 of I8.
MCE or CMCE (I16) may be used to
change the capture data format, D7-
D3 of I28.

INIT

CS4231A Initialization: This bit is read
as 1 when the CS4231A is in a state
in which it cannot respond to parallel
interface cycles. This bit is read-only.

Immediately after RESET (and once the CS4231A

has left the INIT state), the state of
this register is: 010x0000

During initialization and power down, this regis-
ter CANNOT be written and always reads
10000000 (80h)

ID7-ID0

Indexed Data register: These bits are
the indirect register referenced by
the Indexed Address register (R0).

During initialization and power down, this regis-
ter can NOT be written and is always read
10000000 (80h)

INT

Interrupt Status: This indicates the
status of the internal interrupt logic
of the CS4231A. This bit is cleared
by any write of any value to this reg-
ister. The IEN bit of the Pin Control
register (I10) determines whether
the state of this bit is reflected on
the IRQ pin of the CS4231A.
Read States

0 - Interrupt inactive
1 - Interrupt active

PRDY

Playback Data Ready. The Playback
Data register (R3) is ready for more
data. This bit would be used when di-
rect programmed I/O data transfers
are desired.

0 - Data still valid. Do not overwrite.
1 - Data stale. Ready for next host

data write value.

PL/R

Playback Left/Right Sample: This bit
indicates whether data needed is for
the Left channel or Right channel in
all audio data formats except
ADPCM. In ADPCM it indicates
whether the first two or last two
bytes of a 4-byte set (8 ADPCM
samples) is needed.

0 - Right or 3/4 ADPCM byte needed
1 - Left, Mono, or 1/2 ADPCM byte

needed

Index Address Register (R0)

D7

D6

D5

D4

D3

D2

D1

D0

INIT

MCE TRD

IA4

IA3

IA2

IA1

IA0

Indexed Data Register (R1)

D7

D6

D5

D4

D3

D2

D1

D0

ID7

ID6

ID5

ID4

ID3

ID2

ID1

ID0

Status Register (R2, Read Only)

D7

D6

D5

D4

D3

D2

D1

D0

CU/L CL/R CRDY SER PU/L PL/R PRDY INT

CS4231A

DS139PP2

29

«
...
27
28
29
30
31
...
»

Содержание CS4231A













































































Отзывы:

Нет отзывов

Похожие инструкции для CS4231A

Бренд: SAI Страницы: 16

Бренд: N-Com Страницы: 20

Бренд: N-Com Страницы: 28

Бренд: GSK Страницы: 32

Бренд: hotset Страницы: 2

Бренд: Caliber Страницы: 12

Бренд: Easun Страницы: 6

Бренд: Edin Страницы: 20

Бренд: ALLEN & HEATH Страницы: 14

Бренд: KBSOUND Страницы: 2

Бренд: SoundMax Страницы: 43

Бренд: Hama Страницы: 45

Бренд: ELBE Страницы: 19

Бренд: Duro Dyne Страницы: 16

Бренд: PROEL Страницы: 28

Бренд: AMW Страницы: 44

Бренд: Sony Страницы: 13

Бренд: Sony Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды