Crown CT15232, Оригинальное руководство пользователя

Страница: 19 / 132

19
English
Power tool components
1 Ventilation slots
2 Body
3 Carrying handle
4 Lock-off button
5 On / off switch
6 Handle
7 Spindle lock
8 Guard cover
9 Cutting disc *
10 Sliding guard cover
11 Rotary stop
12 Lead screw
13
Tiltable lever
14 Clamping handle
15 Wrench *
16 Screw
17 Protective plate
18 Adjusting bolt
19 Adjusting stop
20 Base plate
21 Locking handle (for carrying)
22 Fasteners of protective plate
23 Cutting depth adjustment bolt
24 Cutting depth adjustment bolt lock-nut
25 Scale
26 Cutting disc fixing bolt
27 Inner flange
28 Spindle
29 External flange
30 Clamping flange
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Carriage position (see fig. 1)
The power tool can be moved only when positioned
for carriage (the body pulled down and fixed). When
moved, the power tool has to be held only by carrying
handle 3 , or underneath baseplate 20 �
Before starting any work, position the power tool for
operation�
• Slightly press handle 6 �
• Move locking handle 21 as shown in fig. 1.
• Lift the body up smoothly�
• To position the power tool for carriage, do the
indicated operations in a reverse order�
Mounting / dismounting of protective plate (see
fig. 2)
• Mount the protective plate 17 using fastening
elements 22 (see fig. 2).
• While dismounting the protective plate 17 , repeat
the operations described above in reverse order�
Adjustment of the cutting depth (see fig. 3)
With the help of the bolt 23 and the lock-nut 24 , adjust
the depth of cut so that the cutting disc 9 in the lower
position does not touch construction components of
the power tool (see fig. 3).
• Loosen lock-nut 24 �
• Adjust the cutting depth by turning bolt 23 in or
out�
• Tighten lock-nut 24 �
Setting of cutting angle (see fig. 4)
• Loosen adjusting bolts 18 by means of the wrench 15
(see fig. 4).
•
Set the required cutting angle turning adjusting
stop 19 � The angle is set according to the indication of
scale 25 �
• Tighten adjusting bolts 18 by means of an wrench 15 �
Setting of cutting width (see fig. 5)
• Unscrew adjusting bolts 18 by means of the
wrench 15 (see fig. 5).
• Select the required width of cut shifting the adjusting
stop 19 �
• Align holes in the adjusting stop 19 with threaded
holes in the base plate 20 , and tighten adjusting
bolts
18
by means of the wrench
15
�
Mounting / replacement of cutting disc (see
fig. 6-7)
After mounting of cutting disc, make a
trial run before commencing operation -
start the power tool and let it work in idle
mode for not less than 30 seconds. The
operation of cutting disc with radial or axial run-
out and causing increased vibration of the power
tool is strictly forbidden.
Wearing protective gloves is recom-
mended for mounting / replacing cutting
disc.
• Lift the body to the uppermost position�
• Lift the sliding guard cover 10 to the uppermost
position and tighten the top screw 16 (see fig. 6).
• Shift the spindle lock 7 to the right and hold it, after
that put the wrench 15 on the bolt 26 and turn it in order
to fix the cutting disc 9 in the fixed position. Press and
hold the spindle lock 7 , unscrew the bolt 26 by means
of the wrench 15 �
• Dismount from the spindle 28 : clamping flange 30 ,
external flange 29 and cutting disc 9 �
• Clean fastening elements with a soft brush and
mount on the spindle 28 : cutting disc 9 , external
flange 29 and clamping flange 30 �
Attention: ensure that the bore di-
ameter of the cutting disc 9 corre-
sponds with the diameter of the spin-
dle 28. Observe the consequence of
parts installation, avoid oblique setting of parts in
the course of mounting and do not turn over the
flanges (see fig. 7).