Crow Shepherd Скачать руководство пользователя страница 47

Страница: 47 / 73

thecrowgroup.com

Page | 46

Report Disarm

only after an Activation

If this option is on, the panel will not normally send an

Arm/Disarm signal to the monitoring company, however, if a

zone alarm occurs the panel will send a Disarm following the

disarming of the panel to show it has been turned OFF by a valid

user

No channel selected

Report Stay Disarm only

after an Activation

If this option is on, the panel will not normally send a Stay Mode

Arm/Disarm signal to the monitoring company, however, if a

zone alarm occurs the panel will send a Stay Mode Disarm

following the disarming of the panel to show it has been turned

OFF by a valid user

No channel selected

Report Access to

Program Mode

If this option is on the panel will report a Contact ID code to

indicate that either Client or Installer program Modes have been

accessed

All channels selected

Report Zone Restores

If this option is on the panel will report all zone restores. If this

option is turned off the panel will only report the alarms

All channels selected

Report Delinquent

If the panel has been configured for Delinquency monitoring and

an area has not been armed for the time set at, a Delinquency

Alarm will be sent to the Monitoring Station

All channels selected

Report Radio Battery

Low

If this option is on the panel will report a Battery Low from any

radio zones that have the battery status monitored

All channels selected

Report Supervised Radio

Alarm

If this option is on the panel will report a Supervised radio Alarm. All channels selected

Report Zone Sensor-

watch Alarm

If this option is on the panel will report a Zone Inactivity (Sensor-

watch) Alarm.

All channels selected

Report Latchkey Disarm

When this option is turned ON and the panel was armed in

Latchkey Report Mode, at Disarming by a non-latchkey user the

specified latchkey disarm report will be sent via voice or SMS

report channel to user, marked as latchkey mode user.

All channels selected

Report Communication

Interference Detected

If the radio receiver detects Communication Interference

(Jamming) of the radio frequency, the panel can report this

event to the monitoring station if this option is turned on

All channels selected

Report Output Fail

If this option is on and a fault is detected on the output, a report

will be sent to the monitoring station if Contact ID is set as the

reporting format

All channels selected

Report Tests

If this option is selected, the panel can send automatic test

connections, but if test connections are not required, they can

be disabled by turning this option off.

All channels selected

Report Stay Mode Zone

Alarms

If this option is on, the panel will report zone alarms in Stay

Mode

All channels selected

Содержание Shepherd










































































Результаты поиска

Содержание Shepherd

Отзывы:

Похожие инструкции для Shepherd

Бренды по названию

Популярные бренды

Crow Shepherd, Руководство по установке

Результаты поиска

Содержание Shepherd

Отзывы:

Похожие инструкции для Shepherd

Бренды по названию

Популярные бренды