Crossfire HD-350, Руководство оператора

Страница: 13 / 21

Page 11
6.3 We l di n g
Observe the voltage and current data of welder whether meet to the requirements of welding norm when
test welding (Refer to Table 5). If not, please adjust knob. It does not weld until meet the requirements.
6.4 We l di n g N o r m
(For Reference) Table 5
Material
Thickness
mm
Wire
Diameter
mm
Liner Inner
Diameter
mm
Liner
Specifications
mm
Current
A
Voltage
V
Gas Flow
l/min
0.8
～
1.5
Φ
0.8
Φ
1.4 1.2
×
1.6
（
blue
）
50
～
90 17
～
18 6
·
1.0
～
2.5
Φ
0.8
Φ
1.4 1.2
×
1.6
（
blue
）
60
～
100 18
～
19 7
2.5
～
4.0
Φ
0.8
Φ
1.4 1.2
×
1.6
（
blue
）
100
～
140 21
～
24 8
·
2.0
～
5.0
Φ
1.0
Φ
1.6 1.2
×
1.8
（
black
）
70
～
120 19
～
21 9
5.0
～
10
Φ
1.0
Φ
1.6 1.2
×
1.8
（
black
）
120
～
170 23
～
26 10
·
5.0
～
8.0
Φ
1.2
Φ
1.6 1.2
×
1.8
（
black
）
110
～
180 22
～
24 10
8.0
～
12
Φ
1.2
Φ
1.6 1.2
×
1.8
（
black
）
160
～
300 25
～
38 12
·
10
～
16
Φ
1.6
Φ
2.0 1.2
×
2.2
（
grey
）
140
～
180 22
～
24 15
＞
16
Φ
1.6
Φ
2.0 1.2
×
2.2
（
grey
）
180
～
400 34
～
40 18
·
Are short circuit transition, the others are grain transition.
6.5 M a i n t e n a n c e a n d S e r v i c e
* The HD series CO
2
welder is a semi-automatic gas shielded welder. To properly operate & maintain the
welder can assure it of good performance and prolong its operating life. Only the qualified personnel are
allowed to be in charge of repairing. It is strongly recommended customers contact with our company or
agent for technical, repairing, accessories supply and service back-up when they feel unable to work out the
technical hitch or problems.
* Maintenance job should be conducted by the trained personnel.
* If the welder is not in use either for a long time or temporarily, it should be kept dry and have good
ventilation to free it from moisture, eroded or toxic gas. The tolerable temperature ranges from
﹣
25
～﹢
55 , and the relative humidity can not be more than 90%.
℃
* Dust removal
The professional maintenance personnel should use dry compressed air (use air compressor or bellows) to
remove the dust inside the machine. The part adhering to grease must be cleaned with cloth while make sure
there are no loose parts ,the machine should be cleaned twice a year.
* Regularly check the input & output cables of welder.
*Don’t pull the feeder device by means of the torch cable.
* Use qualified wire.
* Clean the dust from liner with compressed air regularly (the dust is accumulated by friction between wire
and liner) to assure of even wire feeding.
* Please replace the feed roll if find it wear and tear to prevent wire uneven feeding.
ATTENTION:
* The welder voltage is always higher, so the safety precaution should be taken before repair to avoid
Accidental shock. Under no circumstance can anyone except the professionally trained personnel
open the case of the machine.
* Switch off the power source each time when removing dust.
* No touching inside cable or work piece while removing dust.