background image

1.2   Technical Characteristics

TABLE 1.1  Model 1586-04-0431 RF Attenuator Technical Characteristics

  

EQUIPMENT  SPECIFICATIONS*

EQUIPMENT  SPECIFICATIONS*

  Input  Characteristics

  Input  Characteristics

CH  1,2

CH  3,4

  

Impedance/Return Loss

50

/14 dB

50

/14 dB

Frequency 

0.5-4.0 GHz 

25.0-31.0 GHz

Input No Damage

+20 dBm

+20 dBm

Input Level range

0 to -20 dBm

0 to -20 dBm

Input 1 dB comp, min att

+10 dBm

+10 dBm

  Output  Characteristics

  Output  Characteristics

  Impedance/Return Loss

50 

 /14 dB

50 

 /14 dB

Frequency  (GHz) 

0.5-4.0 GHz 

25.0-31.0 GHz

Output Level Range

-20 to -80 dBm

-20 to -80 dBm

  Channel  Characteristics

  Channel  Characteristics

  Channel  Characteristics

  Attenuation, min.

 

 at Fc

10 ±1 dB

10 ±1 dB

Att. range, 0.5±0.5 dB steps

10 to 70 dB

10 to 70 dB

Freq. Resp. @att range

       10 to 30 dB

±1.5 dB

±1.5 dB

     31 to 50 dB

±2.0 dB

±2.0 dB

       51 to 70 dB

±2.5 dB

±2.5 dB

Att Accuracy @att range, Fc

Att Accuracy @att range, Fc

       10 to 30 dB

±1.0 dB

±1.0 dB

       31 to 50 dB

±1.0 dB

±1.0 dB

     51 to 70 dB

±1.5 dB

±1.5 dB

   

Other

   Temp Coefficient

±0.025 dB/Degree C, max.

Controls, Indicators

  Gain 

Direct readout LCD; pushbutton switches or remote

  

Offset

Shifts attenuation range by the amount of ext attenuator

   Power; Alarm; Remote

Green LED; Red LED; Yellow LED

   Remote

RS232C/RS485/422, 9600 baud (Ethernet Optional)

Other 

   CH 1,2; CH 3,4 Con. 

SMA (female); 2.92 mm (female), 50

   Alarm Connector

DB9 - NO or NC contact closure on Alarm

   Size

19 inch standard chassis 1.75” high X 

19” 

deep

   Power

100-240 ± 10% VAC, 47 - 63 Hz, 

25

 watts maximum

  

*+10 to +40 degrees C; Specifications subject to change without notice

1586-04-0431 Manual 

 

       Page 4

    

          4/12/21

Содержание 1586-04-0431



















Отзывы: