Critical Environment Technologies CGAS-A страница 41 Скачать руководство пользователя

Страница: 41 / 48

Rev. B | 2021.08

cGas Detector Analog Transmitter - Installation Manual

Calibrate Menu

Press Enter

In the Selected Channel menu, if Temperature (or Humidity) is not displayed,

press ENTER and use the UP button to scroll to find the item you are looking for.

Press ENTER.

Selected Channel

CO2

Selected Channel

>Temperature

Selected Channel

>Humidity

Use the UP button to find Temperature Adj (or Humidity Adj). If you want to

change the offset value, press ENTER. Change the offset value using the UP or

DOWN and ENTER buttons.

Temperature Adj

>-4.0 degC

Humidity Adj

>+02 %RH

Press ENTER to confirm the value is correct. If you entered the wrong value,

press the UP button to move the cursor to N and press ENTER and reenter the

value.

Confirm?

>-4.0 degC

Confirm?

>+2 %RH

7.8 Test Functions

7.8.1 Test Analog Output

Testing the analog output allows you to determine if the installation was

successful. The test forces the cGas Detector to output a predetermined signal

to the controller or DDC/BAS to test that the correct signal is being transmitted

and the controller responds as configured (ie. if analog output is configured for

VFD control, the fans operate as expected).

From the main display, press ENTER.

Enter passcode 0001 using the UP button and ENTER button.

Содержание CGAS-A















































Результаты поиска

Содержание CGAS-A

Отзывы:

Похожие инструкции для CGAS-A

Бренды по названию

Популярные бренды

Critical Environment Technologies CGAS-A, Руководство по установке

Результаты поиска

Содержание CGAS-A

Отзывы:

Похожие инструкции для CGAS-A

Бренды по названию

Популярные бренды