manualshive.com logo in svg

Critical Environment Technologies CGAS-A, Руководство по установке

Поделиться
Скачать
Critical Environment Technologies CGAS-A Скачать руководство пользователя страница 19

© 2021 All rights reserved. Data subject to change without notice. 

19

Rev. B | 2021.08 

cGas Detector Analog Transmitter - Installation Manual

Remote PID Sensors

Part Number

Range

TVOCs

ESH-A-SPL

0 - 30 ppm

ESH-A-SPH

0 - 300 ppm

4.3 RH & Temperature Sensor (Option -RHT)

The CGAS-A is a single channel device, it has one analog output. If ordered 

with an internal or remote gas sensor and a relative humidity and temperature 

sensor, the analog output signal will be used to send the gas reading signal to a 

controller or BAS/DDC. Therefore, the RH & temperature readings are for display 

purposes only, there is no current output or communication back to a controller 

or BAS/DDC for RH or temperature readings when a gas sensor is present.

4.4 Calibration Extending Firmware (CEF) and Sensor Aging

The cGas Detector with integral electrochemical sensor(s) have been

programmed with our CEF. This firmware takes into consideration the aging of

the electrochemical CO and NO2 sensors so that less frequent calibrations are

required in less-critical applications such as parking garages. The system tracks

the age of the sensor and automatically compensates for the reduced output of

the sensor as it ages.

Содержание CGAS-A

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды