CrimeStopper CS-2011RS Series III Super Rage Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 30

background image

TACH MODE & TACH FINDER FEATURE

Tach Reference Mode

provides reliable remote starting performance though engine speed sensing. When using

Tach  Reference  Mode,  the  WHITE/RED  wire  is  used  for  Tach  signal  [Engine  RPM]  input.    Most  modern  engines
include  various  points  where  the  Engine  Speed  [Tach]  or  A/C  signal  may  be  obtained.    Tach  Signal  examples:
Negative  (-)  side  of  ignition  coil,  at  the  Distributor  or  Ignition  Control  Module,  Coil  Pack,  Engine  Computer,  or
Crankshaft Sensor.  Sometimes Fuel injection solenoids, and Alternator stator pins can be used.

These Tach Signal

locations mentioned are provided as a guide, your vehicle may differ. Some locations will NOT be a good location
for Tach source due to RF noise or Computer Data. Use the TACH FINDER feature if needed.

TACH FINDER FEATURE:

The Tach Finder mode can assist  you in locating or verifying a Tach source  for  your installation.  Follow the Tach
Finder  steps  below  to  locate  signal.    The  unit  will  begin  to  flash  the  parking  lights  if  you  have  the White/Red  wire
connected to a valid tach source.  If lights do not flash, then try another wire until you locate a tach signal that will
cause the Parking lights to flash.   NOTE: On vehicles equipped with daytime running lights, it may be difficult to see
any  flashing  parking  lights.    In  this  case  your  only  notification  will  be  the  slight  “ticking”  sound  coming  out  of  the
module from the on-board flashing light relay.

TACH FINDER:

1.  Open hood (Ground the Blue Hood Pin wire if no hood pin is installed)
2.  Start Engine with the key.
3.  Press the Program button for 2 seconds
4.  Lights will begin flashing if the White/Red wire is connected to a valid tach
5.  Once Tach is located then turn off engine and close hood to abort.
6.  See Tach Reference programming below.

TACH PROGRAMMING:

1.  Open hood (Ground Blue wire if no hood pin installed.)
2.  Connect WHITE/RED wire to a valid Tach source.
3.  Start engine with key.
4.  Press program button 5 times, then wait for 5 light flashes.
5.  Wait at least one second then push program button again (1) time, you should get a light flash with the button

press. This unit is now at option #1 for Tach Learning.

6. Press the #1 Lock Button on remote transmitter to program Tach.

NOTE:

Pressing the Brake Pedal also

programs Tach.

One Light Flash = Tach Mode. Two Light Flashes = Tachless Mode

.

7. If lights do not flash for confirmation, then try another tach source or try the tach finder feature above.

15

«
...
13
14
15
16
17
...
»

Содержание CS-2011RS Series III Super Rage































Отзывы:

Нет отзывов

Похожие инструкции для CS-2011RS Series III Super Rage

Prestige APS-2K4MS

Бренд: Audiovox Страницы: 6

Бренд: Disney Страницы: 2

Бренд: Orca Страницы: 2

Бренд: Fire-Lite Alarms Страницы: 48

UNGO ProSecurity SR6000

Бренд: Clarion Страницы: 57

Бренд: Capehart Страницы: 5

Бренд: Code Alarm Страницы: 2

Бренд: Code Alarm Страницы: 2

Бренд: Code Alarm Страницы: 2

Бренд: La Crosse Страницы: 5

Бренд: x-sense Страницы: 22

Бренд: Hochiki America Страницы: 2

Бренд: Peakeep Страницы: 2

Бренд: Peakeep Страницы: 5

Бренд: HAL-HEN Страницы: 6

Бренд: Bailey Страницы: 9

Бренд: BALDR Страницы: 69

Бренд: Explore Scientific Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды