background image

 

15 

OPERATING INSTRUCTIONS 

 

TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL) 

To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least 
1½ seconds.  

If the system is armed, pressing Button #3 may or may not trip the alarm system when opening 

the trunk depending on programming option (10).  See page 10. 

 

REMOTE PANIC PROTECTION 

To sound the alarm upon command (panic), press and hold the Button #4 (Panic) for at least 2 seconds until 
the siren sounds.  Press Button #2 (Unlock) to reset panic mode. 

 

PRE-WARNING SHOCK PROTECTION & SENSOR ADJUSTMENT 

If a low-level shock to the vehicle is detected, pre-warning protection will activate sounding 5 quick siren chirps 
and  1  light  flash.    If  a  hard  impact  is  detected  the  shock  sensor  should  trip  the  alarm  system.    Once  it  is 
mounted,  adjust  the  sensor  as  needed  by  turning  the  adjustment  screws  clockwise  to  increase  or  counter-
clockwise  to  decrease  the  sensitivity.    The  sensor  is  also  equipped  with  2  small  indicator  lights  to  ease  the 
adjustment process.  Green light = Pre-warning disturbance (6 siren chirps).  Red light = A full alarm trip. 

 

SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL 

This system can be armed and disarmed without siren chirps on an “as needed” basis.  Press the Bank #2 on 
the side of the remote and within 3 seconds use the lock/unlock buttons to arm/disarm without siren chirps. 

 

PROGRAMMABLE SILENT ARM/DISARM MODE (CHIRP DEFEAT) 

The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp.  See 
alarm programming option (#8) to enable or disable this feature.  See page 10. 

 

EMERGENCY OVERRIDE / DISARM 

If  you  have  lost  the  transmitter  or  it  stops  working  for  any  reason  and  the  Alarm  is  armed,  you  will  have  to 
open the door with the key, which will activate the alarm.  Turn the ignition on and press the override/program 
button  for  about  3  seconds  (until  siren  stops).    The  Alarm  will  disarm.    If  you  continue  to  hold  the  button  for 
additional 3 seconds, the system will enter the Valet mode. 

 

EMERGENCY DISARM WITH CUSTOM OVERRIDE 

If  you  have  programmed  your  system  for  Custom  Override,  follow  the  same  steps  above  (Emergency 
Override) while pressing the valet button 2-15 times as you have programmed.  You must continue to hold the 
button down on the last press for 5 seconds.  The Alarm will disarm and enter the Valet mode, which allows 
you to use the vehicle until you can repair/replace the remote transmitter or have the alarm system checked.   

 

Содержание CS-2002DPII





















Отзывы: