Crevalle Boats 33 CSF Скачать руководство пользователя страница 86

Страница: 86 / 188

Drainage Systems

Console Lounge Seat Storage Compartment

The storage compartment below the forward console

lounge seat is drained overboard by gravity through

a fitting in the hull side.

Forward Below Deck Storage Compartment

The forward storage compartment below the cockpit

sole is drained by gravity to the forward bilge. The

forward bilge is drained overboard by the forward

bilge pump.

Bow Storage Compartments

The forward storage compartments below the port

and starboard bow seats drain by gravity to the

forward bilge.

Rope Locker

The rope locker drains overboard through a drain

fitting in the hull at the bottom of the locker. It is

important to inspect the drain frequently to remove

any accumulated debris.

9.3 Bilge Drainage

There are three bilge pumps, aft, emergency, and

forward. The aft and forward bilge pumps are

activated both manually by switches in the helm

station and automatically by float switches located

near the pump. The automatic float switches are

connected to the house battery bank. They are

protected by “push to reset” circuit breakers in the

battery switch panel and remain activated when

the battery switches are in the OFF position and

the batteries are connected. The manual switches

are supplied current when the House battery

switch is activated. They are protected by fuses

in the digital switch control module.

All bilge pumps pump water out of thru-hulls lo-

cated above the waterline in the hull sides. The

aft bilge pump and automatic switch are located

near the transom. The emergency bilge pump and

switch are located on a shelf behind the aft bilge

pump. The forward pump and automatic switch

are located in the head compartment bilge.

The manual bilge pump switches should be ac-

tivated briefly each time the boat is used. This

will ensure that the pumps are operating properly

and increase the service life of the pumps. The

automatic switches should be manually activated

periodically, by turning the test knob on the side of

switches or flooding the bilge with a garden hose

to verify operation. This is particularly important

before operating the boat offshore.

Anchor Rope Locker Drain

Aft Bilge Pump & Automatic Switch

Содержание 33 CSF





























































































































































































Результаты поиска

Содержание 33 CSF

Отзывы:

Похожие инструкции для 33 CSF

Бренды по названию

Популярные бренды

Crevalle Boats 33 CSF, Руководство пользователя

Результаты поиска

Содержание 33 CSF

Отзывы:

Похожие инструкции для 33 CSF

Бренды по названию

Популярные бренды