Crestron DMPS-100 Скачать руководство пользователя

Страница: 72 / 76

DigitalMedia Presentation Systems

Crestron

DMPS-100/200/300-C/300-C-AEC

•

DigitalMedia Presentation Systems: DMPS-100/200/300-C/300-C-AEC

Operations Guide – DOC. 7219D

10.

At the Toolbox prompt, type

erase

and press

Enter

. The following text

appears in Toolbox:

Erasing
->25%->50%->75%->100%
Done

11.

Click the

icon and select

Firmware…

to display the “Firmware”

dialog box, then click

Browse

12.

Find and select the correct firmware file (.CUZ or .zip) and click

Open

13.

In the “Firmware” dialog box, click

Send

. A “Confirmation” dialog box

opens asking if the right file has been selected. Click

to display the

“File Transfer” dialog box.

14.

When file transfer is completed, a dialog box opens requesting re-

connection. Click

, then close the “Firmware” dialog box and re-connect

using the normal Address Book entry.

Network Analysis

If Cresnet analysis is required, contact Crestron’s True Blue Support.

Battery Replacement

A Lithium battery is used to power the system clock within the

DMPS-100/200/300-C. Under normal conditions, the battery lasts for approximately

10 years. In the event that the clock fails, only an authorized technician should

replace it. Refer to caution statement below.

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type recommended by the manufacturer. Dispose of used

batteries according to the manufacturer's instructions.

Check Network Wiring

Use the Right Wire

To ensure optimum performance over the full range of the installation topology, use

Crestron Certified Wire only. Failure to do so may incur additional charges if

support is required to identify performance deficiencies because of using improper

wire.

Calculate Power

CAUTION:

Use only Crestron power supplies for Crestron equipment. Failure to

do so could cause equipment damage or void the Crestron warranty.

CAUTION:

Provide sufficient power to the system. Insufficient power can lead to

unpredictable results or damage to the equipment. Use the Crestron Power

Calculator to help calculate how much power is needed for the system

(

www.crestron.com/calculators

When calculating the length of wire for a particular Cresnet run, the wire gauge and

the Cresnet power usage of each network unit to be connected must be taken into

consideration. Use Crestron Certified Wire only. If Cresnet devices are to be daisy

chained on the run, the Cresnet power usage of each network unit to be daisy

chained must be added together to determine the Cresnet power usage of the entire

chain. If the unit is run from a Crestron system power supply network port, the

Cresnet power usage of that unit is the Cresnet power usage of the entire run. The

Содержание DMPS-100













































































Результаты поиска

Содержание DMPS-100

Отзывы:

Похожие инструкции для DMPS-100

Бренды по названию

Популярные бренды

Crestron DMPS-100, Руководство по эксплуатации

Результаты поиска

Содержание DMPS-100

Отзывы:

Похожие инструкции для DMPS-100

Бренды по названию

Популярные бренды