Crestron DMPS-100 Скачать руководство пользователя

Страница: 38 / 76

DigitalMedia Presentation Systems

Crestron

DMPS-100/200/300-C/300-C-AEC

•

DigitalMedia Presentation Systems: DMPS-100/200/300-C/300-C-AEC

Operations Guide – DOC. 7219D

Foot Placement for the DMPS-100/200/300-C

NOTE:

No more than two DMPS-100/200/300-C devices should be stacked.

Hardware Hookup

Connect the Device

Make the necessary connections as called out in the illustration that follows this

paragraph. Refer to “Network Wiring” on page 29 before attaching the 4-position

terminal block (

NET

) connectors. Apply power after all connections have been

made.
When making connections to the DMPS-100/200/300-C, use Crestron power

supplies for Crestron equipment.

Hardware Connections for the DMPS-100/200/300-C Front Panels (DMPS-300-C Shown)

Содержание DMPS-100













































































Результаты поиска

Содержание DMPS-100

Отзывы:

Похожие инструкции для DMPS-100

Бренды по названию

Популярные бренды

Crestron DMPS-100, Руководство по эксплуатации

Результаты поиска

Содержание DMPS-100

Отзывы:

Похожие инструкции для DMPS-100

Бренды по названию

Популярные бренды