Crestron CEN-NVS100 Скачать руководство пользователя страница 22

Страница: 22 / 76

Network Video Streamer

Crestron

CEN-NVS100

PTZ Speed Control

NOTE:

If the camera is a fixed camera or does not support PTZ features, PTZ speed

control buttons are not displayed on the home page.

The pan, tilt, and zoom speed drop-down lists allow fine-tuning of the aiming
position of the camera:

•

Pan speed:

Controls the range of the horizontal movement of the camera.

The greater the value, the greater is the angular movement when performing
the Left or Right functions. Values range from –5 to +5.

•

Tilt speed:

Controls the range of the vertical movement of the camera. The

greater the value, the greater is the angular movement when performing the
Up or Down functions. Values range from –5 to +5.

•

Zoom speed:

Controls the range of the zooming. The greater the value, the

greater is the change in the viewing angle. Values range from –5 to +5.

Preset Selection

NOTE:

If the camera is a fixed camera or does not support PTZ features, the

Go to:

preset drop-down list is not displayed on the home page.

The

Go to:

drop-down list allows a camera preset to be selected.

Video and Audio Control Buttons

Video and audio control buttons are described in the following sections.

NOTE:

Audio is not supported in CEN-NVS100 version 0100i.

NOTE:

When Firefox or Safari is used as the Web browser and the CEN-NVS100

is in

MPEG-4

MJPEG

streaming mode, video and audio control buttons are not

supported.

NOTE:

When Internet Explorer is used as the Web browser and the CEN-NVS100

is in

MJPEG

streaming mode, only the

Digital zoom

and

Start MP4 Recording

buttons discussed below are supported.

•

Network Video Streamer: CEN-NVS100

Operations & Installation Guide – DOC. 6873A

Содержание CEN-NVS100













































































Результаты поиска

Содержание CEN-NVS100

Отзывы:

Похожие инструкции для CEN-NVS100

Бренды по названию

Популярные бренды

Crestron CEN-NVS100, Руководство по эксплуатации и установке

Результаты поиска

Содержание CEN-NVS100

Отзывы:

Похожие инструкции для CEN-NVS100

Бренды по названию

Популярные бренды