manualshive.com logo in svg

Crestron Cameo C2N-CBF, Руководство по эксплуатации и установке

Поделиться
Скачать
Crestron Cameo C2N-CBF Скачать руководство пользователя страница 33

Crestron 

C2N/C2NI-CB Series

 Cameo

™

 Keypads

 

Uploading and Upgrading 

NOTE: 

 Crestron recommends that you use the latest software and that 

each device contains the latest firmware to take advantage of the most 
recently released features. Please check the Crestron website 
(

http://www.crestron.com/updates

) for the latest versions of software and 

firmware. New users are required to register to obtain access to this site. 

Assuming a PC is properly connected to the entire system, Crestron 
programming software allows the programmer to upload programs to the 
control system after their development and firmware upgrades to network 
devices. However, there are times when the files for the program are 
compiled and not uploaded. Instead, compiled files may be distributed 
from programmers to installers, from Crestron to dealers, etc. Even 
firmware upgrades are available from the Crestron website as new 
features are developed after product releases. In those instances, one has 
the option to upload via the programming software or to upload and 
upgrade via the Crestron Toolbox.  

The following sections define how one would upload a SIMPL Windows 
program or upgrade the firmware of the Cameo keypad. However, before 
attempting to upload or upgrade, it is necessary to establish 
communications.  

Communication Settings 

NOTE:

 For laptops and other PCs without a built-in RS-232 port, 

Crestron recommends the use of a PCMCIA card over a USB adapter, 
particularly if using Viewport. 

 

The procedure in this section provides details for RS-232 communication 
between the PC and the control system. If TCP/IP communication is 
preferred, consult the latest version of the Crestron e-Control Reference 
Guide (Doc. 6052) or the respective Operations Guide for the control 
system. These documents are available from the Crestron website. Refer 
to the following figure for a typical connection diagram when uploading 
files. 

NOTE:

  Use a standard DB9 male to female “straight-through” cable. 

Operations & Installation Guide - DOC. 6346A 

Cameo™ Keypads: C2N/C2NI-CB Series  

•

  29 

Содержание Cameo C2N-CBF

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды