Cree XLamp MH Series Скачать руководство пользователя страница 2

Страница: 2 / 14

XLAMP

MH FAMILY LED SOLDERING & HANDLING

and the Cree logo are registered trademarks, and

the Cree LED logo is a trademark, of Cree, Inc. XLamp

is a registered trademark of Cree LED. Other trademarks, product and company names are

the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. This document is

provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available at

www.cree-led.com.

CLD-AP193

REV 4

HANDLING XLAMP

MH FAMILY LEDS

Manual Handling

Use plastic, not metal, tweezers to grab XLamp MH Family LEDs at the sides of the substrate, i.e., at the base. Do not touch the optical

surface with tweezers. Do not touch the optical surface with fingers. Do not push on the optical surface.

Cree LED recommends the following at all times when handling XLamp MH Family LEDs or assemblies containing these LEDs:
•

Avoid putting mechanical stress on the LED optical surface.

•

Never touch the optical surface with fingers or sharp objects. The LED optical surface could become soiled or damaged, which would

affect the optical performance of the LED.

•

Cree LED recommends always handling MH Family LEDs with appropriate ESD grounding.

•

Cree LED recommends handling MH Family LEDs wearing clean, lint-free gloves.

Whenever possible, Cree LED recommends the use of a pick & place tool to remove XLamp MH Family LEDs from the factory tape and
reel packaging.

WRONG

CORRECT

Содержание XLamp MH Series















Результаты поиска

Содержание XLamp MH Series

Отзывы:

Похожие инструкции для XLamp MH Series

Бренды по названию

Популярные бренды

Cree XLamp MH Series, Пайка и обращение

Результаты поиска

Содержание XLamp MH Series

Отзывы:

Похожие инструкции для XLamp MH Series

Бренды по названию

Популярные бренды