background image

4

Crathco

®

Simplicity Bubbler

Installation and Set-Up

1.

2.

Place machine on counter with proper spacing.
• The appliance must be placed in a horizontal position.
• The appliance is suitable for indoor use only.

a.

Place dispenser on 
stable counter strong
enough to support
its weight.

b.

Allow 13 cm (5”) on sides
and 15 cm (6”) on back
for proper ventilation.

c.

Position machine away
from heat emitting 
objects (i.e. ovens, grills,
refrigeration equipment).

Install power cord.

a.

Do not use extension cord.

Failure to follow proper installation
guidelines can damage equipment
and void warranty.

Plug cord into power outlet.

b.

Note proper voltage.

Observe machine voltage configuration.
Do not apply improper voltage to
machine or damage to machine will
occur.

1. This appliance is not intended for the use by persons (including children) with reduced physical, sensory, or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by person responsible for their safety.

2. Children should be supervised to ensure that they do not play with the appliance.
3. This appliance is only to be installed in locations where it can be overseen by trained personnel.

5”

(13 cm)

5”

(13 cm)

6”

(15 cm)

6” (15 cm) minimum
machine spacing from
wall

5” (13 cm) minimum
machine spacing from
wall or other machines

Recommended ambient temperature 75° F

(25° C).

Top View

Front View

CAUTION/ ATTENTION/ ATENCIÓN

Содержание Simplicity CS-2D-16

















Отзывы: