background image

TABLE OF CONTENTS

WARNINGS AND SAFETY PRECAUTIONS........................................................................ 3

WARRANTY ......................................................................................................................... 4

A. GENERAL INFORMATION .................................................................................................. 5

B. INSTALLATION RECOMMENDATIONS.............................................................................. 5 - 6

C. OPERATION 

RECOMMENDATIONS .................................................................................. 6

D. MAINTENANCE RECOMMENDATIONS ............................................................................. 6 - 8

TROUBLE SHOOTING......................................................................................................... 9

E. REPLACEMENT PARTS........................................................................................................ 10

RETURNED GOODS POLICY ............................................................................................. 12

Other brand and product names are trademarks or registered trademarks of their respective holders.
® Burks Pumps is a registered trademark of Crane Pumps & Systems, Inc.
© Burks Pumps, Inc. 1997, 2001, 2003                         Alteration Rights Reserved.                                                Printed in U.S.A.

2

Содержание burks pumps WB12













Отзывы: