Crane BARNES BUS Series Скачать руководство пользователя страница 9

Страница: 9 / 16

Control Unit Hookup

When you position the control unit, be sure the charger cord
will reach the AC power outlet and the pump cable and the
fl oat switch will reach the bottom of the sump. Position the
unit in a well ventilated area. (Diagram C)

Mounting the control unit:

(a) Thread the plastic wire tie through the two mounting

brackets on the back of the control unit. (b) Secure the

control unit to the discharge pipe of the main pump by

wrapping the tie around the pipe and pulling it tight.

Positioning the fl oat switch:

The

fl oat switch will turn on the pump when the water

rises to the top of the switch. The switch should be

mounted six inches (6”) above the activation level of the

main AC pump. Attach the fl oat switch very securely to

the discharge pipe or the elbow of the back-up pump with

the plastic wire tie.

Be sure the switch is positioned

vertically with the mounting bracket at the top. Do not

tilt the switch. Do not position the fl oat switch on the

side of the discharge pipe facing the drain tile or any

incoming rush of water!

Installing the battery fl uid sensor:

Replace the battery cap that is 2nd from the POSITIVE

(+) post of the battery with the sensor cap that is provided

in the back-up sump pump package. There are two holes

in the sensor cap. Insert the fl uid sensor in the hole that is

off-center on the top of the cap.

Do not glue the sensor

into the cap.

If your battery will not accommodate the

enclosed cap, you cannot use the battery fl uid sensor,

however you must attach the sensor to the POSITIVE (+)

post of the battery or the alarm will sound continuously.

The Battery Back-up System will not warn you if the fl uid

level is low in this confi guration. You will need to check

your battery monthly to see if it needs water.

Hooking up the pump:

Plug the pump wires into the pump connector on the back

of the control unit.

Hooking up the battery:

Coat the terminals with a little petroleum jelly to prevent

corrosion. Attach the battery cables to the battery. The

BLACK wire to the POSITIVE (+) post, the WHITE wire

to the NEGATIVE (-) post.

6. Immediately plug the charger into the charger hole on the

back of the control unit and into an AC outlet on the wall.

The Back-up Sump Pump System is

ready to use!

Diagram C

Содержание BARNES BUS Series

















Результаты поиска

Содержание BARNES BUS Series

Отзывы:

Похожие инструкции для BARNES BUS Series

Бренды по названию

Популярные бренды

Crane BARNES BUS Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BARNES BUS Series

Отзывы:

Похожие инструкции для BARNES BUS Series

Бренды по названию

Популярные бренды