background image

12

RETURNED GOODS

RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.

CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.

Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary 
Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards 
In Handling Said Material. All Applicable Laws And Regulations Shall Apply.

Limited 2 Year Warranty

We warrant that products of our manufacture will be free of defects in material and workmanship under normal use and 
service for twelve (12) months after notice of owner’s acceptance, but no greater than twenty-four (24) months after receipt 
of shipment, when installed and maintained in accordance with our instructions.
This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state. In the 
event the product is covered by the Federal Consumer Product Warranties Law (1) the duration of any implied warranties 
associated with the product by virtue of said law is limited to the same duration as stated herein, (2) this warranty is a 
LIMITED WARRANTY, and (3) no claims of any nature whatsoever shall be made against us, until the ultimate consumer, 
his successor, or assigns, notifi es us in writing of the defect, and delivers the product and/or defective part(s) freight prepaid 
to our factory or nearest authorized service station. Some states do not allow limitations on how long an implied warranty 
lasts, so the above limitation may not apply. 

THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL 

WARRANTIES WITH RESPECT TO ANY PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. 
POINT OF MANUFACTURE OR AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN 
DEFECTIVE. THERE SHALL BE NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR 
OTHERWISE.

 Unless expressly stated otherwise, guarantees in the nature of performance specifi cations furnished in 

addition to the foregoing material and workmanship warranties on a product manufactured by us, if any, are subject to 
laboratory tests corrected for fi eld performance. Any additional guarantees, in the nature of performance specifi cations 
must be in writing and such writing must be signed by our authorized representative. Due to inaccuracies in fi eld testing 
if a confl ict arises between the results of fi eld testing conducted by or for user, and laboratory tests corrected for fi eld 
performance, the latter shall control. 

RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING 

FROM SYSTEMS ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE 
EXPERIENCE AND PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A 
WARRANTY OF SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN.

This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning 
(d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any 
modifi cation of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor cost 
due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without our prior 
written approval.
This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice 
and\or our specifi c recommendations. The purchaser is responsible for communication of all necessary information 
regarding the application and use of the product. 

UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR 

ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOST PROFITS, LOST 
INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES ARE CAUSED 
BY ANY DEFECTS IN MATERIAL AND\OR WORKMANSHIP AND\OR DAMAGE OR DELAYS IN SHIPMENT. THIS 
WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY, INCLUDING ANY 
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

.

No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, 
without our prior written approval.

IMPORTANT!

WARRANTY REGISTRATION

Your product is covered by the enclosed Warranty.

Complete the Warranty Registration Form and return to

Crane Pumps & Systems, Inc. Warranty Service Group

If you have a claim under the provision of the warranty, contact your local 

Crane Pumps & Systems, Inc. Distributor.

Содержание BARNES BUS Series

















Отзывы: