English
4
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz .......................hertz
min .....................minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
OPM .................... oscillations per
minute
A .........................amperes
W ........................watts
or AC ...........alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
no .......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
Minimum gauge for Cord sets
Volts
Total length of Cord in Feet
(meters)
120 V
25 (7.6)
50 (15.2) 100 (30.5) 150 (45.7)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
American Wire gauge
More
Than
not
More
Than
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
Your CRAFTSMAN buffer/polisher has a precision-built
electric motor and it should be connected to a 120-volt,
60-Hz AC ONLY power supply (normal household current).
DO NOT operate on direct current (DC). The large voltage
drop will cause a loss of power and the motor will
overheat. If the tool does not operate when plugged into
correct 120-volt, 60-Hz AC ONLY outlet, check the power
supply. This buffer/polisher has a 2-wire power cord (no
adapter needed).
Intended Use
This buffer/polisher is intended solely for residential buffing
and polishing.
sPECiFiCATiOns
Pad Diameter
10" (254 mm)
Motor OPM
2800
Rating
120 volts, 60 Hz AC
Amps
1
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Proper Hand Position (Fig. B)
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
use proper hand position as shown.
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of a
sudden reaction.
Proper hand position requires both hands on the
perimeter handle
2
.
Fig. B
2
Speed Dial (Fig. A)
The speed dial
5
changes the speed of the buffer/polisher.
Rotate the dial forward to increase the speed or backward
to decrease the speed. 1 is the lowest setting and 4 is the
highest setting.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Содержание CMEE100
Страница 27: ......
Страница 28: ...CRAFTSMAN 701 East Joppa Road Towson MD 21286 Copyright 2019 01 19 Part No N635394 ...