English
5
Additional Safety Information
WARNING: ALWAYS
use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or dust
mask if operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
•
Scabbard/Guide Bar Cover -
Enclosure fitted over guide
bar to help prevent tooth contact when saw is not in use.
•
Kickback -
The backward or upward motion, or both
of the guide bar occurring when the saw chain near the
nose of the top area of the guide bar contacts any object
such as a log or branch, or when the wood closes in and
pinches the saw chain in the cut.
•
Kickback, Pinch -
The rapid pushback of the saw
which can occur when the wood closes in and pinches
the moving saw chain in the cut along the top of the
guide bar.
•
Kickback, Rotational -
The rapid upward and backward
motion of the saw which can occur when the moving saw
chain near the upper portion of the tip of the guide bar
contacts an object, such as a log or branch.
•
Limbing -
Removing the branches from a fallen tree.
•
Low-Kickback Chain -
A chain that complies with the
kickback performance requirements of ANSI B175.1–2012
(when tested on a representative sample of chain saws.)
•
Normal Cutting Position -
Those positions assumed in
performing the bucking and felling cuts.
•
Notching Undercut -
A notch cut in a tree that directs
the tree’s fall.
•
Rear Handle -
The support handle located at or toward
the rear of the saw.
•
Reduced Kickback Guide Bar -
A guide bar which has
been demonstrated to reduce kickback significantly.
•
Replacement Saw Chain -
A chain that complies with
kickback performance requirements of ANSI B175.1–2012
when tested with specific chain saws. It may not meet
the ANSI performance requirements when used with
other saws.
•
Saw Chain -
A loop of chain having cutting teeth, that
cut the wood,and that is driven by the motor and is
supported by the guide bar.
•
Ribbed Bumper -
The ribs used when felling or bucking
to pivot the saw and maintain position while sawing.
•
Switch -
A device that when operated will complete or
interrupt an electrical power circuit to the motor of the
chain saw.
•
Switch Linkage -
The mechanism that transmits motion
from a trigger to the switch.
•
Switch Lockout -
A movable stop that prevents
the unintentional operation of the switch until
manually actuated.
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
•
Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water.
Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING:
Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.
WARNING:
Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use.
Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
•
Air vents often cover moving parts and should
be avoided.
Loose clothes, jewelry or long hair can be
caught in moving parts.
•
An extension cord must have adequate wire size
(AWG or American Wire Gauge) for safety.
The smaller
the gauge number of the wire, the greater the capacity
of the cable, that is, 16 gauge has more capacity than 18
gauge. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. When using
more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
