Craftsman 486.24331 Скачать руководство пользователя страница 12

Страница: 12 / 16

OPERATION

KNOW YOUR SPIKER SPREADER

Read this owner's manual and safety rules before operating your Spiker Spreader.

Compare the illustration below with your Spiker Spreader to familiarize yourself with the various controls and their
locations.

FLOW CONTROL LEVER

Opens and closes the flow

plate at the bottom of the hopper.

LIFT HANDLE

Raises the unit for transport or lowers it

for spreading and aerating.

PLASTIC WING NUT

Tightens at desired setting to

control how far the flow control lever can open the flow
plate.

HOW TO USE YOUR SPIKER/SPREADER

• Refer to the instruction label on the material package

and to the instruction decal on your spreader to help
determine the proper spreader setting and application
rate. Also see the Setting Chart on page 13 of this
manual for a general range of settings for commonly
used materials.

• Determine the approximate square footage of the

area to be covered and estimate the amount of
fertilizer or seed required.

• Move the spreader to the area where application is to

begin.

FIGURE 24

FLOW CONTROL LEVER

PLASTIC WING NUT

LIFT HANDLE

• Loosen the plastic wing nut and move it to the desired

setting. Retighten the nut. See figure 24.

• Making sure the flow control lever is in the "OFF"

position, fill the hopper, breaking up any lumps.

• Lower the aerator spikes to the operating position.
• Start the spreader in motion and then move the

flow control lever to the "ON" position (against the
plastic wing nut) as you travel across your lawn. The
recommended towing speed is 3 m.p.h.

• Do not make sharp turns with spikes in the ground.
• Raise aerator spikes to transport position when

crossing over concrete or other hard surfaces.

• Do not aerate if the ground is extremely hard or dry.

If ground is too dry, sprinkle or water for one to two
hours prior to use.

• Do not aerate if the ground is too wet (muddy).

IMPORTANT:

Always place flow control lever in the

"OFF" position to prevent excess fertilizer from being
released when filling the spreader and when stopping or
turning.

ALIGN AND TIGHTEN WING NUT
AT DESIRED FLOW SETTING

10 11

12 13

14 15

16 17

OFF

WING NUT SET AT "5"

Содержание 486.24331

















Результаты поиска

Содержание 486.24331

Отзывы:

Похожие инструкции для 486.24331

Бренды по названию

Популярные бренды

Craftsman 486.24331, Руководство пользователя

Результаты поиска

Содержание 486.24331

Отзывы:

Похожие инструкции для 486.24331

Бренды по названию

Популярные бренды