background image

6 – English

opERAtIoN

 

Do not use tool if trigger does not actuate properly. 

Any tool that cannot be controlled with the trigger is 
dangerous and must be repaired.

 

check operation of the workpiece contact 
mechanism frequently. 

Do not use the tool if the 

workpiece contact mechanism is not working correctly 
as accidental driving of a nail may result. Do not 
interfere with the proper operation of the workpiece 
contact mechanism.

 

Do not use a tool that does not work correctly.

 

Always assume that the tool contains nails.

 

Do not carry the tool from place to place holding 
the trigger.

 Accidental discharge could result.

 

Always handle the tool with care:

•  Respect the tool as a working implement.
•  Never engage in horseplay.
•  Never pull the trigger unless nose is directed toward 

the work.

•  Keep others a safe distance from the tool while tool 

is in operation as accidental actuation may occur, 
possibly causing injury.

 

choice of triggering method is important. check 
manual for triggering options.

 

the brad nailer is designed for single-hand use. 

Do 

not hold the tool by the front of the magazine. Do not 
put hands, head, or other parts of your body near the 
bottom of the magazine where the nail exits the tool, as 
serious personal injury could result.

 

Do not point the tool toward yourself or anyone 
whether it contains nails or not.

 

Do not actuate the tool unless you intend to drive a 
nail into the workpiece.

 

Always ensure that the workpiece contact is fully 
positioned above the workpiece.

 Positioning the 

workpiece contact only partially above the workpiece 
could cause the nail to miss the workpiece completely 
and result in serious personal injury.

 

Do not drive nails near edge of material. 

The 

workpiece may split causing the nail to ricochet, 
injuring you or a co-worker. Be aware that the nail may 
follow the grain of the wood, causing it to protrude 
unexpectedly from the side of the work material or 
deflect, possibly causing injury.

 

Do not point the tool toward yourself or anyone 

whether it contains nails or not.

 

Do not actuate the tool unless you intend to drive a 

nail into the workpiece.

 

Always ensure that the workpiece contact is fully 

positioned above the workpiece.

 Positioning the 

workpiece contact only partially above the workpiece 

could cause the nail to miss the workpiece completely 

and result in serious personal injury.

 

Do not drive nails near edge of material. 

The workpiece 

may split causing the nail to ricochet, injuring you or a co-

worker. Be aware that the nail may follow the grain of the 

wood, causing it to protrude unexpectedly from the side 

of the work material or deflect, possibly causing injury.

 

Keep hands and body parts clear of immediate 
work area. 

Hold workpiece with clamps when 

necessary to keep hands and body out of potential 
harm. Be sure the workpiece is properly secured 
before pressing the fastener against the material. The 
workpiece contact may cause the work material to shift 
unexpectedly. 

 

Keep face and body parts away from back of the 
tool cap when working in restricted areas.

 Sudden 

recoil can result in impact to the body, especially when 
nailing into hard or dense material.

 

During normal use the tool will recoil immediately 
after driving a fastener. this is a normal function 
of the tool. 

Do not attempt to prevent the recoil by 

holding the nailer against the work. Restriction to the 
recoil can result in a second fastener being driven from 
the nailer. Grip the handle firmly, let the tool do the 
work and do not place second hand on top of tool or 
near exhaust at any time. Failure to heed this warning 
can result in serious personal injury.

 

Do not drive fasteners on top of other fasteners or with 
the tool at an overly steep angle as this may cause 
deflection of fasteners which could cause injury.

loADING tool

 

Do not load the tool with fasteners when any one of 
the operating controls is activated.

When loading tool:

 

Never place a hand or any part of body in fastener 
discharge area of tool.

 

Never point tool at anyone.

 

Do not pull the trigger or depress the workpiece 

contact as accidental actuation may occur, possibly 
causing injury.

SAvE tHESE INStRuctIoNS 

  Refer to them frequently and use them to instruct 

others who may use this tool. If you loan someone this 
tool, loan them these instructions also.

NAIlER SAFEtY WARNINGS

Содержание 315.FS2000





























Отзывы: