Craftsman Marine CM4.65 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

background image

32 Crafted with CRAFTSMAN MARINE

10 Preparations for the new season

1. Open the fuel supply cock.

2 Charge the battery(ies), if necessary.

3. Connect the battery cables.

4. Verify that the cover of the raw water cooling
strainer is tightened well.

5. Insert the impeller that you have removed during
winterpreparation (page 24). Verify the tightness of the
raw water pump cover and of all drain plugs.

6. If you have disconnected any hoses before winter
storage, these must all be connected again and
tightened well.

7. Open the seacock of the raw water entry.

8. Check the level of the cooling liquid, as described
on page 23.

9. Make sure that the engine has sufficient lubrication
oil, as described on page 20.

10. Start  the  engine  and  make  sure  that  there  are  no
leaks  in  the  fuel  system,  the  cooling  system  and  the
exhaust  assembly.  Place  a  bucket  underneath  the
exhaust  exit  to  catch  any  excessive  antifreeze  while
starting the engine. Anti freeze is poisonous and must
be disposed of correctly.

11. Verify the proper functioning of all electronic parts
and all engine instruments. Also verify the proper
functioning of the mechanical remote control of throttle
and gearbox.

12. Check exhaust for cooling water.

8.

5.

«
...
30
31
32
33
34
...
»

Содержание CM4.65

















































Отзывы:

Нет отзывов

Похожие инструкции для CM4.65

Бренд: Garmin Страницы: 14

Бренд: Navistar Страницы: 197

Бренд: WÄRTSILÄ Страницы: 232

Бренд: Kohler Страницы: 116

Бренд: Plettenberg Страницы: 26

Бренд: Chery Страницы: 55

Бренд: Parker Страницы: 32

Бренд: Bosch Страницы: 106

rexroth MSK 030

Бренд: Bosch Страницы: 72

Rexroth MKE Series

Бренд: Bosch Страницы: 134

Бренд: Bosch Страницы: 82

Бренд: Bosch Страницы: 124

Rexroth MKE E Series

Бренд: Bosch Страницы: 138

Бренд: Oriental motor Страницы: 8

Бренд: Oriental motor Страницы: 12

Бренд: Germany Motions Страницы: 12

BEVELMASTER 204B

Бренд: TRI tool Страницы: 46

Бренд: TOHATSU Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды