Craftsman Marine CM4.65 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 48

background image

35

Crafted with CRAFTSMAN MARINE

Problems and solutions

Problem

Probable cause

Solution

4. Engine starts running but with
irregular cycles or it stops again

5. Engine does not arrive at maxi-
mum revolutions under full load

•  Empty fuel tank
•  Air in the fuel system
•  Fuel filter clogged up with water and/or dirt
•  Leaking fuel supply or fuel injection line
•  Defective injector/injection pump
•  Breather line of fuel tank clogged up
•  Fuel line clogged
•  Incorrect valve clearance
•  Idling revolutions too low
•  Exhaust clogged up
•  Poor fuel quality or polluted fuel
•  Filter of electrical fuel lift pump is clogged

•  Air in the fuel system
•  Fuel filter clogged up with water and/or dirt
•  Leakage in fuel supply line or fuel injection line
•  Setting of stop valve incorrect
•  Oil level too high
•  Incorrect SAE-specification or quality of lubrication oil
•  Incorrect valve clearance
•  Clogging in the exhaust
•  Insufficient quantity of combusition air
•  Poor fuel quality or polluted fuel
•  Incorrect injection moment
•  Leakage of air intake manifold
•  Engine overload

•  Fill the tank
•  Check / bleed the system
•  Check / clean or replace
•  Check and replace, if necessary
•  Check and clean or replace
•  Check /remove blockage
•  Check / remove blockage
•  Readjust
•  Readjust
•  Check / remove blockage
•  Check fuel quality. Drain fuel tank and rinse it well.

Fill with good quality fuel

• Check / clean

•  Check and bleed the system
•  Clean or replace
•  Check and replace, if necessary
•  Check / reset
•  Drain suffcient oil quantity
•  Replace by engine lubrication oil of good quality
•  Adjust
•  Check / remove clogging
•  Check air inlet and ventilation openings in engine

room

• Check fuel quality. Drain fuel tank and rinse it well.

Fill with good quality fuel

•  Check / readjust
•  Replace manifold or gasket, as applicable
•  Check dimensions of boat propeller

11

«
...
33
34
35
36
37
...
»

Содержание CM4.65

















































Отзывы:

Нет отзывов

Похожие инструкции для CM4.65

Бренд: BAFANG Страницы: 12

Plug & Play Plus

Бренд: CHERUBINI Страницы: 16

Бренд: MTU Страницы: 239

Бренд: IMS Страницы: 6

dunkermotoren D258

Бренд: Ametek Страницы: 8

Бренд: Volvo Penta Страницы: 29

Бренд: Volvo Penta Страницы: 56

Бренд: Volvo Penta Страницы: 96

Бренд: O.S. engine Страницы: 13

MAX-15CV Series

Бренд: O.S. engine Страницы: 30

Бренд: MULTIPLEX modell Страницы: 11

Бренд: O.S. engine Страницы: 38

Бренд: Honda Страницы: 61

Бренд: Royal Enfield Страницы: 152

Бренд: FAAC Страницы: 8

Бренд: Ober Страницы: 32

EMF SQML160 Series

Бренд: EMF Motor Страницы: 43

Бренд: Yanmar Страницы: 394

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды