Craftsman Marine CM4.65 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 48

background image

24 Crafted with CRAFTSMAN MARINE

Maintenance and inspection

8

The rubber impeller of the raw water cooling circuit
must be inspected every year and when the volume of
cooling water coming out of the wet exhaust seems to
be decreasing or the engine cooling seems inadequate.

Check-up of raw water pump impeller

Impeller removal

Re-installation impeller

•  Close the seawater inlet cock
•  Loosen the screws of the cover
•  Remove the cover and use an impeller removal tool

to remove the impeller.

• Inspect the impeller blades for cracks and replace if

necessary.

• When the impeller is damaged, be sure any rubber

residues are removed from the pump housing and
water pipes before replacing the impeller.

• Use a silicone spray to lubricate the impeller before

fitting

•  Fit the impeller to the pump shaft
•  Fit cover while placing a new gasket
•  Open the seawater inlet cock

The rubber impeller should never
run dry! If the water supply has been
blocked (closed seacock, etc) the
impeller may need replacement.

ALWAYS CARRY A SPARE IMPELLER
ON BOARD! (AA.480.90021)

AA.480.90021

«
...
22
23
24
25
26
...
»

Содержание CM4.65

















































Отзывы:

Нет отзывов

Похожие инструкции для CM4.65

Бренд: Stihl Страницы: 40

Бренд: Atlas Copco Страницы: 156

Бренд: Schartec Страницы: 16

Бренд: Baratza Страницы: 5

RIO Bravo IP Engine

Бренд: SAS Страницы: 19

Бренд: CAB Страницы: 16

Lombardini LGW 523 MPI

Бренд: Kohler Страницы: 144

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Volvo Penta Страницы: 96

Бренд: Volvo Penta Страницы: 106

Бренд: Jets Munt Страницы: 24

Бренд: Lycoming Страницы: 155

Бренд: Robin America Страницы: 23

Бренд: Valach Страницы: 24

LMG 14000 MONOFASE

Бренд: LOMBARDINI MARINE Страницы: 78

Бренд: Honda Страницы: 5

Бренд: Honda Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды