background image

page 3

4. Mounting Plate Installation.

ON

OFF

ON

OFF

Turn off circuit breakers to current fixture from 
breaker panel and be sure operating light switch is 
turned to the OFF position.

WARNING

: Failure to disconnect power supply prior to 

installation may result in serious injury.

Remove existing fixture. 

WARNING

: When using an existing outlet box, be sure 

the outlet box is securely attached to the building 
structure and can support the full weight of the fan. 
Ensure outlet box is clearly marked "Suitable for Fan 
Support." If not, it must be replaced with an approved 
outlet box. Failure to do so can result in serious injury.

CAUTION

Be sure outlet box is grounded properly 

and that a ground wire (

GREEN

 or bare) is present.

Install mounting plate to outlet box using original 
screws, spring washers and flat washers provided 
with new or original outlet box.* Pull electrical 
wiring from outlet box through center hole in the 
mounting plate.

Locate screw on outer edge of mounting plate 
closest to the j-hook and remove that screw. Then, 
remove screw on outer edge of mounting plate 
directly opposite the screw that was just removed. 
Partially loosen the other 2 screws.

*

Note

: It is very important that you use the proper 

hardware when installing the mounting plate as this 
will support the fan.  

3. Installation Preparation.

This fan can be mounted as a 

flushmount

 on a 

regular (no-slope) ceiling 

only

Downrod 

installations are 

not

 available for this fan.

Installation requires these tools:

Phillips screwdriver, flat-head screwdriver, 
adjustable pliers or wrench, stepladder, wire 
cutters, and rated electrical tape.

downrod

installation

flushmount

installation

CANNOT be

installed on

angled or

vaulted ceilings

To prevent personal injury and damage, ensure 
that the hanging location allows the blades a 
clearance of 7ft. (2.13m) from the floor and 30in. 
(76cm) from any wall or obstruction. 
This fan is suitable for room sizes up to 400 square 
feet (37.2 square meters).

spring washers

flat washers

outlet box screws

mounting plate

blade edge

7 feet

(2.13m)

(76cm)

30

inches

12 f

t.

 - 20 f

t.

12 ft. - 20 ft.

(3.66m - 6.1m)

(3.66m - 6.1m)

Содержание TMPH44BNK5





















Отзывы: