background image

4. Hanging Bracket Installation.

page 3

ON

OFF

ON

OFF

3. Installation Preparation.

Vaulted ceiling 
angle is not to 
exceed 25 degrees.  

downrod

installation

flushmount

installation

hanging bracket

7 feet

(2.13m) (76cm)

30 

inches

12f

t.

  - 20f

t.

12ft. - 20ft.

(3.66m - 6.1m)

(3.66m - 6.1m)

blade edge

Turn off circuit breakers to current fixture from breaker panel 
and be sure operating light switch is turned to the OFF 
position. 

WARNING: 

Failure to disconnect power supply prior to 

installation may result in serious injury.

Remove existing fixture. 

WARNING:

 When using an existing outlet box, be sure the outlet 

box is securely attached to the building structure and can 
support the full weight of the fan. Ensure outlet box is clearly 
marked "Suitable for Fan Support." If not, it must be replaced 
with an approved outlet box. Failure to do so can result in serious 
injury.

CAUTION

Be sure outlet box is grounded properly and that a 

ground wire (green or bare) is present.

Install hanging bracket to outlet box using original screws, 
spring washers and flat washers  provided with new or 
original outlet box.

If installing on a vaulted ceiling, face 

opening of hanging bracket towards high point of ceiling. 
Arrange electrical wiring around the back of the hanging 
bracket and away from the hanging bracket opening.

*Note

: It is very important that you use the proper hardware 

when installing the hanging bracket as this will support the fan. 

To prevent personal injury and damage, ensure 
that the hanging location allows the blades a 
clearance of 7 feet (2.13m) from the floor and 
30in. (76 cm) from any wall or obstruction. 
This fan is suitable for room sizes up to 400  square 
feet (37.2 square meters).

Installation requires these tools:

Phillips screwdriver, flathead screwdriver, 
adjustable pliers or wrench, stepladder, wire 
cutters, and rated electrical tape.

This fan can be mounted with a 

downrod

on a regular (no-slope) or vaulted ceiling.  The 
hanging length can be extended by purchasing 
a longer downrod (0.5in./1.27cm diameter). 
Other installation, such as

 flushmount

, is 

not

 

available for this fan.

spring washers

outlet box screws

flat washers

Содержание SAP62





















Отзывы: