Crafstman 917.270750 Скачать руководство пользователя страница 26

Страница: 26 / 60

ENGINE

TO ADJUST THROTTLE CONTROL

CABLE

The throttle control has been preset at the

factory and adjustment should not be

necessary. Check adjustment as de
scribed below before loosening cable. If

adjustment is necessary, proceed as

follows:
• With engine not running, move throttle

control lever to fast position.

• Check that swivel is against stop. If it is

not, loosen cable clamp screw and pull

cable back until swivel is against stop.

Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the

factory and adjustment should not be

necessary. Check adjustment as described

below before loosening cable. If adjust
ment is necessary, proceed as follows:
• With engine not running, move choke

control (located on dash panel) to full

choke position.

• Loosen knob and remove cover

assembly from air cleaner.

• Choke should be closed. If it is not,

loosen casing clamp screw and move

choke cable until choke is completely

closed. Tighten casing clamp screw

securely.

• Replace air cleaner cover assembly and

tighten knob.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your

engine does not operate properly due to

suspected carburetor problems, take your

tractor to an authorized service center for

repair and/or adjustment.
High speed stop is factory adjusted. Do

not adjust - damage may result.

IMPORTANT:

Never tamper with the

engine governor, which is factory set for

proper engine speed. Overspeeding the

engine above the factory high speed

setting can be dangerous. If you think the

engine-governed high speed needs

adjusting, contact your nearest authorized

service center/department, which has

proper equipment and experience to make

any necessary adjustments.

Содержание 917.270750





























































Результаты поиска

Содержание 917.270750

Отзывы:

Похожие инструкции для 917.270750

Бренды по названию

Популярные бренды

Crafstman 917.270750, Руководство пользователя

Результаты поиска

Содержание 917.270750

Отзывы:

Похожие инструкции для 917.270750

Бренды по названию

Популярные бренды