Crafstman 917.270750 Скачать руководство пользователя страница 7

Страница: 7 / 60

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left

unassembled for shipping purposes. To ensure safe and proper operation of your

tractor all parts and hardware you assemble must be tightened securely. Use the

correct tools as necessary to insure proper tightness. Review the video cassette before

you begin.

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly

easier. Standard wrench sizes you need

are listed below.
(1) 9/16" wrench

(1) Utility knife

(1) 3/4” socket with

drive ratchet

(2) 1/2" wrench

(1) Pliers

(1) Tire pressure

gauge

When right or left hand is mentioned in

this manual, it means, from your point of

view, when you are in the operating

position (seated behind the steering

wheel).

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

• Remove all accessible loose parts and

parts boxes from shipping carton.

• Cut, from top to bottom, along lines on

all four corners of shipping carton, and

lay panels flat.

• Check for any additional loose parts or

boxes and remove.

BEFORE REMOVING TRACTOR

FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND

BOOT
• Slide extension shaft onto lower

steering shaft. Align mounting holes in

extension and lower shafts and install 5/

16 hex bolt and locknut. Tighten

securely.

• Place tabs of steering boot over tab

slots in dash and push down to secure.

INSTALL STEERING WHEEL

• Position front wheels of the tractor so

they are pointing straight forward,

• Remove steering wheel adapter from

steering wheel and slide adapter onto

steering shaft extension.

• Position steering wheel so cross bars

are horizontal (left to right) and slide

inside boot and onto adapter.

• Assemble large flat washer, 3/8 lock

washer, 3/8 hex bolt and tighten

securely.

• Snap steering wheel insert into center of

steering wheel.

• Remove protective materials from

tractor hood and grill.

IMPORTANT;

Check for and remove any

staples in skid that may puncture tires

where tractor is to roll off skid.

Insert

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY

• Lift seat pan to raised position and open

battery box door.

• If this battery is put into service after

month and year indicated on label (label

located between terminals) charge

battery for minimum of one hour at 6-10

amps. (See "BATTERY" in Maintenance

section of this manual for charging

instructions).

Содержание 917.270750





























































Результаты поиска

Содержание 917.270750

Отзывы:

Похожие инструкции для 917.270750

Бренды по названию

Популярные бренды

Crafstman 917.270750, Руководство пользователя

Результаты поиска

Содержание 917.270750

Отзывы:

Похожие инструкции для 917.270750

Бренды по названию

Популярные бренды