Crafstman 917.270750 Скачать руководство пользователя страница 24

Страница: 24 / 60

Gearshift Lever

Neutral

Lock Gate

Adjustment
Bolt

TO ADJUST STEERING WHEEL

ALIGNMENT

If steering wheel crossbars are not

horizontal {left to right) when wheels are

positioned straight forward, remove

steering wheel and reassemble per

instructions in the Assembly section of this

manual

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has

occurred to affect the front wheel toe-in or

camber, contact your nearest authorized

service center/department.

TO REMOVE WHEEL FOR REPAIRS

• Block up axle securely.
• Remove axle cover, retaining ring and

washers to allow wheel removal (rear

wheel contains a square key - Do not

lose).

• Repair tire and reassemble.
• On rear wheels only; align grooves in

rear wheel hub and axle. Insert square

key.

• Replace washers and snap retaining

ring securely in axle groove.

• Replace axle cover.

NOTE:

To seal tire punctures and prevent

flat tires due to slow leaks, tire sealant

may be purchased from your local parts

dealer. Tire sealant also prevents tire dry

rot and corrosion.

Washers

Retaining

Ring

Axle Cover

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK

BATTERY
^CAUTION:

Lead-acid batteries

generate explosive gases. Keep spari<s,

flame and smoking materials away from

batteries. Always wear eye protection

when around batteries.

If your battery is too weak to start the

engine, it should be recharged. (See

"BATTERY" in the MAINTANCE section of

this manual).

If “jumper cables” are used for emergency

starting, follow this procedure;

IMPORTANT:

Your tractor Is equipped

with a 12 volt negative grounded system.

The other vehicle must also be a 12 volt

negative grounded system. Do not use

your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -
• Connect each end of the RED cable to

the POSITIVE (+) terminal of each

battery, taking care not to short against

chassis.

• Connect one end of the BLACK cable to

the NEGATIVE (-) terminal of fully

charged battery.

• Connect the other end of the BLACK

cable to good CHASSIS GROUND,

away from fuel tank and battery.

TO REMOVE CABLES, REVERSE

ORDER -

• BLACK cable first from chassis and

then from the fully charged battery.

• RED cable last from both batteries.

Positive Terminal

Negative Terminal

Chassis

Positive Terminal

Cables

Charged

Battery

Negative Terminal

Содержание 917.270750





























































Результаты поиска

Содержание 917.270750

Отзывы:

Похожие инструкции для 917.270750

Бренды по названию

Популярные бренды

Crafstman 917.270750, Руководство пользователя

Результаты поиска

Содержание 917.270750

Отзывы:

Похожие инструкции для 917.270750

Бренды по названию

Популярные бренды