CPS SCH Series Скачать руководство пользователя страница 112

Страница: 112 / 116

108

SCH100KTL-US-600

SCH125KTL-US-600

Enclosure Protection Degree

NEMA Type 4X

Cooling Method

Variable speed cooling fans

Operation Temperature

Range

-22°F to +140°F/- 30°C to +60°C (derating from

+113°F/+45°C)

Storage Temperature Range

-40F to +158°F/-40°C +70°C maximum

Operating Humidity

0-95%, non-condensing

Operating Altitude

8202ft / 2500m

Display and Communication

User Interface and Display

LED Indicators, APP

Inverter Monitoring

Modbus RS485 / PLC Option

Site Level Monitoring

CPS Flex Gateway (1 per 32 inverters)

Modbus Data Mapping

SunSpec/CPS

Remote Diagnostics / FW

Upgrade Functions

Standard with CPS Flex Gateway

Mechanical Data

Dimensions (WxHxD) (mm)

42.7*24.3*11.2in (1085*616*283.5mm )

Weight (kg)

158lbs/72kg

Mounting/Installation Angle

15- 90 degrees from horizontal

Safety

Safety and EMC Standard

CSA-C22.2 NO.107.1-16, UL Std. No. 1741,

CSA TIL M-07, FCC CFR 47 part15, ANSI C63.4-2014

Grid Standard and SRD

IEEE 1547a-2014, IEEE1547-2003(R2008), IEEE1547.1-

2005(R2011), IEEE1547.1a-2015, CA Rule 21 and UL1741

Supplement AS, ISO-NE

"Max. AC Apparent Power" rating at an operating voltage and temperature range of -30°C to +40°C (-

22°F to +104°F) can output.

The "Output Voltage Range" and "Output Frequency Range" may differ according to the specific grid

standard.

Wye can support the TT/TN-C/TN-S/TN-C-S, Delta cannot support Grounding system.

GFCI in AC Switchgear required for Floating AC systems.

Содержание SCH Series





















































































































Результаты поиска

Содержание SCH Series

Отзывы:

Похожие инструкции для SCH Series

Бренды по названию

Популярные бренды

CPS SCH Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SCH Series

Отзывы:

Похожие инструкции для SCH Series

Бренды по названию

Популярные бренды