Cozzia EC-326G-CO страница 9 Скачать руководство пользователя

Страница: 9 / 58

No response

when pressing

the keys on the

remote

controller.

①

The terminals and wires are poorly

connected.

②

The PCB in the remote controller fails.

①

Plug the terminal securely or

replace the wires.

②

Replace the remote controller.

Back rest

cannot be

reclined or

raised

①

The terminals of reclining actuator and

wires are poorly connected.

②

The reclining actuator fails.

③

Main PCB fails.

①

Plug the terminal securely.

②

Replace reclining actuator.

③

Replace main PCB.

Foot rest

cannot be

raised or

lowered.

①

The terminals of foot rest actuator and

wires are poorly connected.

②

The foot rest actuator fails.

③

Main PCB fails.

①

Plug the terminal securely.

②

Replace foot rest actuator.

③

Replace main PCB.

No vibration by

the motors in

the seat-pad.

①

Print motors fail.

②

The terminals and wires are poorly

connected or the wires fail.

③

Main PCB fails.

①

Replace the print motor.

②

Plug the terminal securely or

replace the wires.

③

Replace main PCB.

No gas charging

in the seat-pad.

①

The terminal of the snuffle valves and

wires are poorly connected.

②

The snuffle valves fail.

③

The inflator pump fails.

④

Main PCB fails.

①

Plug the terminal securely.

②

Replace the snuffle valves.

③

Replace the inflator pump.

④

Replace main PCB.

Содержание EC-326G-CO



























































Результаты поиска

Содержание EC-326G-CO

Отзывы:

Похожие инструкции для EC-326G-CO

Бренды по названию

Популярные бренды

Cozzia EC-326G-CO, Руководство по техническому обслуживанию

Результаты поиска

Содержание EC-326G-CO

Отзывы:

Похожие инструкции для EC-326G-CO

Бренды по названию

Популярные бренды